Jump to content
SAU Community

Recommended Posts

hey guys,

i recently bought a turbo tech manual boost controller off ebay, and loosened the screw all the way (0.7bar), however when i have the boost controller installed, my car develops a big misfire...

Is there any obvious cause for this?

mods: bosch 040, turboback exhaust, pod

Link to comment
https://www.sau.com.au/forums/topic/324825-t-piece-boost-controller/
Share on other sites

I would say 10 PSI and no tune = BAD

Restrictive exhaust would not help and the manual boost controllers are known to spike so could be way more boost and leaning out. (Not a big fan, better to use electric one)

You realy need a tune before you do damage.

You pretty much answered the question yourself "missfire". A missfire is a poor spark, so either your spark plugs need replacing or your 15 year old coilpacks aren't up to the job anymore, or both.

Edited by PM-R33
I would say 10 PSI and no tune = BAD

Restrictive exhaust would not help and the manual boost controllers are known to spike so could be way more boost and leaning out. (Not a big fan, better to use electric one)

You realy need a tune before you do damage.

it wont be running lean. more boost sends things rather rich with the stock ecu and turbo.

as PM-33 said, poor spark. i'm assuming its under full load around 4500-600rpm? if so the most likely culprit are tired coilpacks. can try taping/siliconing them or get new ones. in the meantime you can gap your plugs down a bit.

have a search around here, theres countless threads on this

hey guys thanks for the replies,

i have recently just replaced my spark plugs gapped to 108mm, i sussed out the coil packs and there are no visible hairline cracks etc.. in them.

With the stock boost solenoid, with the exhaust my car runs 7psi <4500rpm, then above 4500rpm it goes to 10psi... and starts to 'misfire' when its on 10psi.

also cleaned the A/F meter, replaced the fuel filter, air filter and reset the ECU.

Edited by shaun123
hey guys thanks for the replies,

i have recently just replaced my spark plugs gapped to 108mm, i sussed out the coil packs and there are no visible hairline cracks etc.. in them.

With the stock boost solenoid, with the exhaust my car runs 7psi <4500rpm, then above 4500rpm it goes to 10psi... and starts to 'misfire' when its on 10psi.

also cleaned the A/F meter, replaced the fuel filter, air filter and reset the ECU.

the coils may look ok, but may not be ok. try taping them up with electrical tape and see if that helps at all, but my guess is that you'll be up for new coils.

Leave your coil covers off and run the engine at night in the dark.

Enjoy the electrical storm.

Id be testing plugs regapped to 0.8mm first though, before you put the coil covers on have a look for sparks arcing around the coil packs.

I also run a smear of dielectric grease on the ends of my coil packs to help stop spark loss on both my GTR and XR6.

had the same issue.

Fixed by gapping the plugs to 0.8. Also smeared a thin layer of high-temp silicone gasket-making crap around the square block part of each coilpack (theres a thread somewhere in the DIY section), since I had them out anyway.

gap plugs then put it in 5th gear at 50kph then floor it. if it missfires then it will missfire badly under this load and its gona be your coilpack. just spend about $250 bucks on a set of heavy duty dsr coils. they are some of the best

gap plugs then put it in 5th gear at 50kph then floor it. if it missfires then it will missfire badly under this load and its gona be your coilpack. just spend about $250 bucks on a set of heavy duty dsr coils. they are some of the best

This sounds like an excessively bad way to diagnose the issues sure it might work but the strain on the motor/gearbox would be stupid. 50kph in 5th and full throttle lol

This sounds like an excessively bad way to diagnose the issues sure it might work but the strain on the motor/gearbox would be stupid. 50kph in 5th and full throttle lol

Its actully what the mechanics do to try help diagnose the problem. Probly the least stressfull on the engine as well. How would it be more of a strain at 1500 rpm then at 4500 rpm? Takes you about a second to find out how badly its missfiring. And then you can fix it. Unless you want to continously thrash your car finding out how badly its missfiring. And pretty sure it wouldnt have a problem with the gearbox. How would it?

heavy duty dsr coils? what are these? (other than a crapload cheaper than splitfires and yellow jackets)

I got them off trademe coz im in NZ and my mate has them in his 25det gts4. My engine runs absolutely perfect and i wouldnt have anything else to be honest. Nothing is going to out perform them for how much power i have. PLus they are like 400 bucks cheaper then yellow jacket and stuff lol

no, you are correct. stock turbo @ 10psi on stock ecu is fine 99% of the time. there will be the odd car that will hit rich and retard at this level, but very few, and this can come down to innacuracy of the boost gauge (may be reading 10psi but the car is actually boosting 11 or 12psi)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is possibly 55 degrees for the Nismo version. I had a look through the manual and the stocker has a breakaway torque of 2.5 to 3.5kgm. Supposedly the Nismo LSD goes down to 5kgm when worn in but it is pretty grabby even with very little throttle. Worse when cold. So I guess you have three things. 1. Shims. 2 Friction plates 3. Cams Would think shims would be the easiest but Ive no clue how many tenths of a mm shim thickness change equals how many kgm torque. Also not sure if the Nismo friction plates are similar/different to stock or if they are the most of the source of the diff being angry. Think I can write off the Nismo rebuild kit for the standard diff as not being what I want.  
    • Yeah, it was a bit of confusion with me, I rang and asked if they had a boot for a soft top, and then the paint shop when they rang and were asked if it had a hard top on it, which it does, just not a PRHT....LOL Meh, whilst frustrating for all concerned it isn't a war stopper and should be a thing of the past in a week or two In other N/A related news, car is booked in at the end of the month for the cams, springs, retainers, harmonic balancer and retune  I might even pull the lazy arse card and get them to do a full service on it whilst it is there
    • Factory LSD is supposedly a 2 way with a very conservative cam. If you've already tried adding friction modifier to the diff oil and it still locks up too much for your liking you might want to adjust the ramp rate on the cam to be more like OEM instead of reducing initial torque even further. People claim the 8 kgf-m disc kit for the OEM LSD is still very streetable but I've never been able to compare everything side by side on my own.
    • Oh man, at least it sounds they've accepted they stuffed up and not put it back on you...could see some confusion if they asked if it had a hardtop or not, and you've answered truthfully but maybe not answering their real question which is what roof did it have from the factory! Glad your keeping it N/A 2.5
    • Nah, I much prefer colour matched Talking about colour matching stuff, the new/used boot lid turned up, all painted up perfectly......aaaannnndddd, it's for a power retractable hard top, not a soft top.....LOL They are now sending a boot to fit a soft top.....,  whilst frustrating, life is like that sometimes, sometimes you just need to dodge, duck, dip, dive and, ummm, dodge.
×
×
  • Create New...