Jump to content
SAU Community

Chatter Noise Under Load


Recommended Posts

Hi All,

I was driving my R33 home from work today and noticed when accelerating from 80 - 100 in 5th under heavy load there was a chatter coming from the engine bay somewhere. Not too sure what it is but I did notice that my A/F ratio is running pretty rich (13 - 13.5)

I took off the pod recently and put back the stock airbox however I think the SAFC was tuned with the pod on.

Any thoughts on what the sound might be?

Link to comment
Share on other sites

14.7 is stoich, but you only use that for cruise. when it comes to putting load on in a turbo car then you want things to be 12 or less (anything higher than about 12.5 at high boost and rpm is going to have a short life), however at 80 to 120kmh in 5th gear you are pretty low in the revs so 13.5 probably wouldn't be too far off the mark.

what did the noise actually sound like? was is like a marble in a tin can? if so then that is most likely pinging, which is bad. however if it starts doing it more often in other gears and rev ranges then you may have a broken manifold stud and the sound is the gasket vibrating.

if the sound was more like it was misfiring then it's either your coils or spark plugs

Link to comment
Share on other sites

Cheers mate,

Ill check it again during lunch and give a better description.

Ill also get someone to tell me the A/F ratio during high boost...I really dont want to be screwing the engine.

Link to comment
Share on other sites

It may be pinging as Marc said. If so, you can top up your fuel with extra toluene (methylbenzene) just to check.

Alternatively, octane booster can be used; but 1x bottle will make little difference. 2x bottles are needed to check.

If pinging ceases, then your state of tune will need to be rectified.

Link to comment
Share on other sites

thanks for the replies guys,

when driving home on some nice road it didn't really sound like marbles in a can. oddly enough the only sort of sound I can compare it to was two pieces of paper hitting each other really quickly. It also isn't a constant noise.

Ill put some octane booster in over the weekend to see if it helps.

Might also go through the engine bay to see if anything is loose.

Link to comment
Share on other sites

  • 2 weeks later...

Well I finally got one of the NVH guys at work out over lunch to listen to the chatter.

Found out that the sound of coming from the gearbox/gear stick.

When I am accelerating in 5th gear and push the gear stick up and to the left the chatter sound becomes worse but when the gear stick is pulled slightly downward it goes away.

We were thinking it may be gear boot related. Has anyone else had this issue before?

Cheers

Link to comment
Share on other sites

Is it completely gone in 4th?

There are bearings (cluster bearings?) in the gearbox that can get pretty noisy in all gears except 4th (where there is no load on them)

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • People still have Skylines? I thought they're non-existent now. 
    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
×
×
  • Create New...