Jump to content
SAU Community

Recommended Posts

Hi All,

I was driving my R33 home from work today and noticed when accelerating from 80 - 100 in 5th under heavy load there was a chatter coming from the engine bay somewhere. Not too sure what it is but I did notice that my A/F ratio is running pretty rich (13 - 13.5)

I took off the pod recently and put back the stock airbox however I think the SAFC was tuned with the pod on.

Any thoughts on what the sound might be?

Link to comment
https://www.sau.com.au/forums/topic/325312-chatter-noise-under-load/
Share on other sites

14.7 is stoich, but you only use that for cruise. when it comes to putting load on in a turbo car then you want things to be 12 or less (anything higher than about 12.5 at high boost and rpm is going to have a short life), however at 80 to 120kmh in 5th gear you are pretty low in the revs so 13.5 probably wouldn't be too far off the mark.

what did the noise actually sound like? was is like a marble in a tin can? if so then that is most likely pinging, which is bad. however if it starts doing it more often in other gears and rev ranges then you may have a broken manifold stud and the sound is the gasket vibrating.

if the sound was more like it was misfiring then it's either your coils or spark plugs

It may be pinging as Marc said. If so, you can top up your fuel with extra toluene (methylbenzene) just to check.

Alternatively, octane booster can be used; but 1x bottle will make little difference. 2x bottles are needed to check.

If pinging ceases, then your state of tune will need to be rectified.

thanks for the replies guys,

when driving home on some nice road it didn't really sound like marbles in a can. oddly enough the only sort of sound I can compare it to was two pieces of paper hitting each other really quickly. It also isn't a constant noise.

Ill put some octane booster in over the weekend to see if it helps.

Might also go through the engine bay to see if anything is loose.

  • 2 weeks later...

Well I finally got one of the NVH guys at work out over lunch to listen to the chatter.

Found out that the sound of coming from the gearbox/gear stick.

When I am accelerating in 5th gear and push the gear stick up and to the left the chatter sound becomes worse but when the gear stick is pulled slightly downward it goes away.

We were thinking it may be gear boot related. Has anyone else had this issue before?

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Man that dinner was such a long time ago....2010! I would only replace the rubber coolant lines with silicone these days; cheap, readily available and will last for ever. You will need new hose clamps though eg https://justjap.com/products/cooling-pro-silicone-engine-heater-hose-set-black-nissan-r32-gtr-rb26dett
    • I wouldn't look too hard at what they did with the R32 GTR in endurance racing in Australia... Lots of things weren't actually available from the factory in the way those cars ran them... Japan also followed what Fred Gibson was doing here with some of there endurance cars in Japan... Australia is also the reason for things like the Brembo brakes, and the change in the gearbox... And quite a few other tricks they used to pull. There's a few other SAU peeps still on these forums that will have heard the stories direct from Alan Heaphy, Fred Gibson, and Jim Richards when we were lucky enough to have a great dinner with them
    • For all the talk of "these parts are junk" I generally recommend OEM because it's really not as bad as claimed. I have never seen or heard of a case like the N63 where the oil returns completely clog with coked oil for example in ~10 years or less. Would it be nice if it were a straighter path? I guess, but most modern cars use a scavenge pump instead of a pure gravity return. Also the factory lines that would be relatively simple to convert to braided are generally speaking hardlines from the factory. I would consider braided line to be a regression, not an improvement. It's also been engineered such that all the hardlines have appropriate strain relief where needed. There's absolutely room for improvement, for example the HKS advantage heritage intake piping shows just how much can be done to make the turbos fight each other less in OEM twin turbo configuration and reduce compressor surge but it's rarely a simple/straightforward process. I recommend looking at what the group A/N1 cars did, generally speaking the changes they made were necessary and proven in endurance racing.
    • Yes, multi relays needed, and possibly a diode. I'm not actually going to think about it though.
×
×
  • Create New...