Jump to content
SAU Community

Just Bought An R33 Skyline Gts25t - Pics, Specs And Help Needed :)


Recommended Posts

yeh dude its andrew, thought it was you things been pretty cruisy how bout your self

yeh good mate,

guys noticed when there cars been driven around for a while and i park i can hear a ticking sound coming from the motor - im guessing its the lifters - how bad a problem is this? does it mean the engine is probably a little tired? its meant to have a geniuine 68kms according to autoworx

could be - the last owner did service it at Kmart Tyre and Auto - god knows what sh*t they put in it.

Tune + Service on Friday so il let the guys at AllStar Garage know all the issues and see what happens

Edited by s13-steve

That sounds about right for the engine mods you have? You don't have an aftermarket ECU, if you got a full aftermarket ECU and got rid of that SAFC Neo, upped the boost a bit, then you would probably get a bit closer to 280.

That sounds about right for the engine mods you have? You don't have an aftermarket ECU, if you got a full aftermarket ECU and got rid of that SAFC Neo, upped the boost a bit, then you would probably get a bit closer to 280.

Doubt it.. 260rwhp give or take, is pretty much on the money. Try a different dyno and you might get 280 :)

the dyno sheet the previous owner gave me from Xspeed was 278rwhp so i was expecting something around that...

ah well 260rwhp is 193rwkw so not to bad i guess, just doesnt feel any faster then my CA18 which had 196rwhp

Doubt it.. 260rwhp give or take, is pretty much on the money. Try a different dyno and you might get 280 :)

Yeh, thought it would be pretty much correct. Does a SAFC Neo prevent boost cuts so you can run higher boost though? Surely with a stand-alone aftermarket ECU you could run a bit more timing and boost, bring it a bit closer to 280?

Yeh, thought it would be pretty much correct. Does a SAFC Neo prevent boost cuts so you can run higher boost though? Surely with a stand-alone aftermarket ECU you could run a bit more timing and boost, bring it a bit closer to 280?

The SAFC should allow you to raise your afm cut (it's not boost cut damnit! :)) as you're bending the afm signals, so the cut threshold would be proportionatly higher.

A full aftermarket ECU would allow you to wind some timing in to it but whether you would see top end gains with the 25 turbo already so close to its' limits would remain to be seen. Generally, being able to adjust timing helps with getting bigger turbos on boost (i.e. improve midrange).

Like I said, another dyno might give you a reading of 280rwhp but they are just tuning tools, not comparison tools.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome Jan, It's very likely that you are in over your head. You'll just have to learn to swim hard and fast! These old rust buckets have more ways to bankrupt us than almost any other car. But hopefully there's nothing wrong that ruins the whole show! We can help a fair bit. There's plenty here who've been fixing these things for >25 years. cheers
    • Hi all. First off, thanks for reading my post. So end of last season I put the car away knowing I was leaking at least two fluids. One of them being rear turbo's oil. I went to my car recently that is waiting in a garage to take a peek with my boroscope to try and see if I can narrow down the souce of oil before taking it out of storage. What I found is not so great I think. The rear turbo is (probably) leaking from the oil drain. The hose and it's clamps are probably the original ones, so most likely just worn out or loose. However I spotted a line of rust going straight down from the turbo oil feed, as if water leaked out of there at some point. Also explains the red liquid that was dripping from my front subframe, which I initially thought was power steering. I can even see coolant drops hanging off the side of the oil pan as well. After a quick hit on the web I found a select few discussions about porous engine blocks. My question is if the pics of the turbo oil feed and the left hand side of the block (imgur link below) looks like it could be exactly that to you. Maybe someone in the community has seen it before and knows what it looks like. If it actually is a porously leaking block, has anyone attempted at fixing it with simple methods like putting a sealer in the cooling system and using something like jb weld on the block surface, or will it just leak in 2 weeks again? I could not find any detailed info or pictures on this topic. If I need a new engine, tell me softly. https://imgur.com/a/knVvmZ8
    • Hey all. I'm 23 and from Germany, September last year I bought a mildly modded 1995 GTR Vspec. Looks great and was fun so far, but I already have a list of issues of various severity that I need to take care of, potentially growing longer the closer I look. I just hope I'm not in over my head, I really want to keep the car and work towards it becoming great. I hope y'all will help me out in getting there, I am positive I will need help sooner rather than later to figure out how to proceed. greetings, some pics of the car I posted to imgur. https://imgur.com/a/StKkabz
    • Would be interesting what the price would be without the barracuda wheels. Looks like he dropped it down to 40k. Maybe his mate wasn't correct about the 50k evaluation. Has always been a dream of mine to own an auto 33. Looks like I'll have to keep saving my pocket money or ask mum for more pocket money.
    • Thinking about importing a stagea as a family car since i’m getting married this year, thoughts? Me and my fiance both like stageas, but don’t have any experience with them
×
×
  • Create New...