Jump to content
SAU Community

Recommended Posts

  • Replies 121
  • Created
  • Last Reply

Top Posters In This Topic

I'm hoping to be there but I need to find out why the bank took so much of my paycheck this week and if they'll let me have it back.

For those who don't know (I had to look it up) the meet point is in Epping, I believe. Helpful for those with GPSs.

Hi,

Do you happen to remember what the latest checkin time is?

I remember rocking up pretty late last time, around 11AM, and it was still very busy, I didn't find any SAU people so left. And then I found out the next day the track gets better around 1-2PM :rofl2:

Sorry I don't remember. Haven't been for a few years.

Also, if anyone wants to come spectate I'm happy to give em a lift.

Can pick you up as long as you live somewhere between Hurstbridge and Somerton with a little detour able to be taken.

I'll be coming back a bit earlier too which might be good for some. I have to be back in Melb by 6pm so will be leaving about 3-3:30.

^Sure thang!

Adam, even if you don't have a helmet, there are passanger groups, if someone can lend theirs to you and you might get a ride in one of our cars :)

Oh, and I might like to try going as passanger in a few cars too, apparantly it's scary :)

do they have seats there, or should i bring a fold out one

Probably not a bad idea to take a seat.

And a very warm jacket too.

I'm going to suss out a garage on the day. Anyone know how much extra they are and how many cars fit into one?

Bring seats, I wouldn't worry about booking a garage... there are garages that you pay for then there are undercover 'car port' areas that are free then there are open spaces. The free undercover areas should be fine and it's only saying a couple of showers for the day (I'm guessing those showers wont be in Winton).

do they have seats there, or should i bring a fold out one

was there a few weeks ago for the drifting, no seating at all.

Its a shitty track for spectators.

Edited by W0rp3D
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
    • Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
Ă—
Ă—
  • Create New...