Jump to content
SAU Community

Recommended Posts

Hi all.

I'm brand new to turbo cars, never driven one before, so got a question to ask the experts in here. I'm looking to get a R32/R33 gtst and just test-driven a 93 R33 gtst. It seems to me that the car is pretty draggy in 1st gear and things only started to pick up in 2nd. I don't know if it's me or the car cause I didn't go past the 3500 mark in 1st (I never like to push someone else's car too hard), though I did feel the boost kicking in at 4000.

So just like to ask all here if it's normal for turbo cars to feel a little draggy before the 4000 mark and if this happens to N/A versions.

Thanks all!

Link to comment
https://www.sau.com.au/forums/topic/326515-question-about-boost-cars/
Share on other sites

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

stock turbo supposed to be spooling from 2500rpm... 4000rpm sounds a bit late. that's the downside of some modified ones where the bigger aftermarket turbo don't start spooling till later, it may give higher output but only at top end rpm for drag racing strips, but will go like an old dog on start and go traffic on the street.

if any dropkick gets in a car I've got for sale and starts taking it to 5500-6000rpm constantly the only thing he can expect is to be left by the curbside with a black eye.

as said before, stock turbos will give you a noticeable increase in induction by 2500 RPM ("start spooling" in layman's terms) and should reach peak in the high 4000 RPM area ("full boost" in layman's terms). If it's not doing this, then it's either modified with a larger turbo, got an aftermarket boost controller, or sporting a boost leak somewhere that's preventing the turbo functioning optimally.

if any dropkick gets in a car I've got for sale and starts taking it to 5500-6000rpm constantly the only thing he can expect is to be left by the curbside with a black eye.

as said before, stock turbos will give you a noticeable increase in induction by 2500 RPM ("start spooling" in layman's terms) and should reach peak in the high 4000 RPM area ("full boost" in layman's terms). If it's not doing this, then it's either modified with a larger turbo, got an aftermarket boost controller, or sporting a boost leak somewhere that's preventing the turbo functioning optimally.

+1

prob best description there for your answer mate! :blush:

a bog stock GTST is fairly nimble in terms of aggressive power and "woosh"

that is, from factory, its setup to drive very normal like and give even power increase

so you wont feel it magically "come on boost" or "wheelspin" instantly like some would expect

its only when you tune the stock ecu, modify it, increase boost and un-restrict the motor, that it behaves like that

Thanks guys! Very informative. Maybe I'll try to push it a little more for the next ones, but with the seller being comfy with it first, of course. I didn't ask the seller if everything's stock or not. But i guess a leak might be the most possible reason cause the car's really feeling draggy at 1st gear, feels much worse than my N/A MR2. 1500 - 3000 feels almost the same.

Thanks all once again!!

Give it a poke.

My r33 is essentially stock and doesn't start pulling really hard until 3500+rpm.

While you would never flog a car during a test drive, you would want to hold the wellie against the fire wall once or twice to make sure the car revs and pulls cleanly through the entire rev range. To not do would be silly.

Right.... point taken. Thanks.

Give it a poke.

My r33 is essentially stock and doesn't start pulling really hard until 3500+rpm.

While you would never flog a car during a test drive, you would want to hold the wellie against the fire wall once or twice to make sure the car revs and pulls cleanly through the entire rev range. To not do would be silly.

Also if you're afraid to push it, after you have taken the car for a drive to see if everything is in order, get the owner to take you for a drive and tell him you want to feel full boost.

Yep, this is what I do.

I drive it nice and easy, feel the gearbox, the steering, listen for noises etc. Then I ask the owner to "show me what its got", usually gives a good idea what sort life its had with the previous owner too.

if any dropkick gets in a car I've got for sale and starts taking it to 5500-6000rpm constantly the only thing he can expect is to be left by the curbside with a black eye.

as said before, stock turbos will give you a noticeable increase in induction by 2500 RPM ("start spooling" in layman's terms) and should reach peak in the high 4000 RPM area ("full boost" in layman's terms). If it's not doing this, then it's either modified with a larger turbo, got an aftermarket boost controller, or sporting a boost leak somewhere that's preventing the turbo functioning optimally.

Considering you quoted the same rpm range as I did in my previous post on this thread, I'm hoping that your post was not partially directed at me. At no point did I tell the OP to thrash the living crap out of a car he is inspecting, but rather to at some stage or another during the test drive to push it past his 3000rpm he mentioned.

Of course, if it wasn't partially directed at me, good response.

What I like to do is to ask the owner to drive the car "Hard" so I can get a good feel for it even if it's in the passenger seat. I think it's rude to thrash someone else's car especially if you don't even know that person but if you are going to spend the money to buy the car you want to make sure the engine is still in good nick and there is no problems at high revs.

Lolol I thrashed some curries 300zx on a test drive with jiz boy (think I told you a out it shan). I'm talking bouncing off limiter and taking a corner sideways. All he said nervously was "I have never driven my car like this" twas hilarious :D

Lolol I thrashed some curries 300zx on a test drive with jiz boy (think I told you a out it shan). I'm talking bouncing off limiter and taking a corner sideways. All he said nervously was "I have never driven my car like this" twas hilarious :bunny:

Haha good times bro! His face was priceless :)

That ZX actually pulled hard though. I think we were both surprised.

Hey LNah - I recognise your username from the MR2 forums. Don't tell them that you're going from an MR2 to a Skyline or you'll cop shit ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Reading your posts Josh, sometimes I feel like I've gone in a time machine back to the 90's when everyone was doe-eyed and figuring things out for the first time.  I've lost track of how many single turbo GTR's I've seen on track that haven't burnt down lol. Everything has been figured out a long time ago. These things are at the point now where its essentially turn-key to go single turbo. 
    • Among other things yes. Making sure to either use an oil pressure regulator or the right restrictor size for your oil pump/range of oil viscosities you intend to run, making sure you plumb the lines correctly, turbo should be placed such that it siphons properly even when the water pump isn't turning so you don't boil coolant in the turbo after shutdown, oil return should be low resistance and also preferably picking the one that is most likely to return to the pickup as opposed to some other irrelevant part of the pan. It's far from impossible to figure this out but I have seen people really, really struggle and if that's the case it's easier to just take the path of least resistance. To me, bolt-on twin turbos are a fixed cost whereas single turbo is almost unbounded.
    • Latest round of updates on the car. I purchased and installed a SWS clutch slipper to help with 60ft times and got some second-hand good condition 275/40R17 Hoosier DR2 radials. Test and tune in November showed the tyres were an upgrade over my over 15 year old mickey Thompson's and I got a 1.8 second 60ft and pb et of 11.71 but even then, that run wasn't great due to rain and driver error (the event got called off 10 minutes later fast forward to the weekend just gone 25th of Jan and there was finally a break in the weather to let racing happen. The first run the track was slippery and only managed a 12.1@129 Second run the track was better and got a new pb et and mph: 11.54@131   Lith and I then worked out that I installed the previously mentioned clutch slipper incorrectly and its never been working, and I had just been dumping the clutch the entire time, we also noticed it was on street boost and not race boost. So I lined up for a third run with the car turned up in the first two gears, but the passengers side axle objected to clutch dumps and left the chat which stopped my weekend.   so there will be another attempt in the future once I replace the tyres as they rubbed and are stuffed now. but a low 11 should be on the cards.
    • Ceramic coating and heat shielding, you mean?
    • Turbos don't require pulling the motor apart so that's "easier". I would recommend the Nismo R3 turbos instead if you want to do stock twin turbo. It doesn't make as much power as the 2530s but it's only like ~50 whp off the mark and should have better response (ball bearing CHRA, slightly smaller turbo). A local that went with a Garrett G30 and 6boost manifold recently nearly burned his car to the ground after the hood insulator started melting and and burning so if you go single turbo I recommend doing a lot of research and validation work to make sure you don't do the same.
×
×
  • Create New...