Jump to content
SAU Community

Recommended Posts

Hey guys i want to dial out some understeer on my R33 4 door it has the following fitted

Front camber kit

Castor rods

rear camber kit

rear toe kit

sub frame bushes

whiteline Rear sway bar 22mm set on hard setting

Whiteline Front sway bar 24mm set on medium (cant ajust more need the sperical bearing link kit)

has kyb shocks and lowered springs but changing to HSD HR coilovers

Its not that bad and heaps better then it was before but i just want to balance it so i have even understeer to oversteer or tiny bit more oversteer to understeer ;)

Alinment settings

2.5 front camber

1.25 rear camber

1mm toe rear (2mm total toe)

0 toe front

+5 front castor

Thanks guys

Put the stock front sway bar back on :P

I have only had time to fit my rear sway bar so the front is standard, and boy it oversteers like a whore!! Would be a good drift car haha

Edited by Harey
  • 2 weeks later...

Yes its a Road car :)

Just some low budget 215 45 R17s on 7.5" rim

running 40psi front little bit better but still bit more understeer than over steer.

i cant set the sway bar softer until i buy a new link kit for the front because the stock links wont reach the softest setting hole on the bar :)

i have picked up some BC racing BR series coilovers i am going to fit these and see if there is any change because i think one of my front shocks is leaking ;)

Just some low budget 215 45 R17s on 7.5" rim
Those won't help.
i have picked up some BC racing BR series coilovers i am going to fit these and see if there is any change because i think one of my front shocks is leaking :wub:
Those will probably make it worse. Stiffening the front end will only increase the understeer characteristics.

i am just saving up for some Federal 595's or some KU36's for the front, its already on the hard setting on the rear so i cant go any stiffer than that.

my lowered springs are about 1.5 inches lower at the front then the rear and the rear have a softer spring rate would have affect it?

Yes softer rear suspension will contribute to understeer.

I would recommend you put on Bilstein shocks at the front if your current ones are buggered. As said previously, stiff coilovers will just make it understeer more.

Plus stiffen up your rear suspension, eg stiffer rear springs.

Edited by Harey
Yes softer rear suspension will contribute to understeer.

I would recommend you put on Bilstein shocks at the front if your current ones are buggered. As said previously, stiff coilovers will just make it understeer more.

Plus stiffen up your rear suspension, eg stiffer rear springs.

Less rear spring actually makes a car gradually oversteer as opposed to to much spring which makes it snap oversteer.

Too much front spring will cause understeer, but usually mid corner not entry.

If we are talking about a road car and your complaing of understeer, go buy some GOOD tires and watch the problem disapear. You could not possibly be pushing the car into a window where sway bars and springs are going to effect the handling if the tires are budget........

Yeah better tyres are a priority at this stage just deciding on wheels before forking out for tyres.

its good on the street but poped up when i took the car drifting at driving sports event, i am fitting up the coilovers because the car setup i thought was to soft and felt a bit boaty trying to follow through to the next corner.

once i get better front tyres do you guys think i should increase front or decrease front camber?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
×
×
  • Create New...