Jump to content
SAU Community

Recommended Posts

uvUtLl.jpg

wont look like this for long :)

vuHOel.jpg

nipples for map sensors installed

9OHWzl.jpg

26WdUl.jpg

tried to get them as flush as possible

fyjwql.jpg

Got some piping made up, just need to buy some pod filters and the intake side of things is done

AaVTJl.jpg

thats all ive got done so far, waiting on nissan to deliver my gaskets and injector o-rings

Was just wondering where you got your MAFless induction pipes from? Very nice build up so far too. Im doing a major overhaul/restore on my gtr too, will start a build thread soon :)

Hey mate,

those pipes were just some spares i had lieing around (ive wrecked a few performance cars and few odd bits and bobs that i couldnt sell have found a new home at my workshop lol)

i had to cut them shorter and weld on a quarter inch reduction on the turbo side so the rubber piping fits onto them. The rest of the piping is 3" which is what most pod filters are anyway.

Well AFMs shit me :) and the fact that the driveability of the car is now better is a justified reason on its own now but i was planning on doing a big single conversion however i cant afford to do that atm. Ive got half of it done now, just a matter of time before i get enough money to go for a big single and get a re-tune.

The boost control is alot better now btw. It spikes quite hard to 1.5bar on a cold night in 2nd gear but in 4th is stabilises around 1.35bar. On the dyno was reading 1.30bar and 1.20bar at redline though but its still running on the rich side. Great tune, has never knocked once, on startup i get like 100 knock but i think thats from the starter motor but generally my knock while the car is running never goes over 27.

My old ecu used to get some false knock during driving, i think its because it was old maybe?

  • 3 weeks later...

all i can say it well done and i very much enjoyed reading this thread, its easily got some of the sexiest+toughest midnight 33R's ive seen thus far. im very jealous having to stick with my gts-t due to my pathetic excuse of an apprentice income. :ermm:

im in the same boat buddy :ermm:

Nothing wrong with a knock level of 27. Anything over 40 will get me worried but on a cold night it never goes over 20 no matter how hard im driving it and im very happy with that.

Theres a possibility that your low knock level is due to a too conservative tune? (if that makes any sense) Room for more power maybe?

How much power are you making and on what boost?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The max they would go for me is 50.
    • That cannot have been a fun set of drilling. The stock "baffle" looks identical to rb26, I just cut fuel cell foam to fit the full length under the baffle.
    • I understand your sarcastic exasperation. But to be fair - the baffles do indeed fit OEM cam covers. They did omit to say that you need to do a bunch of stuff. But they do fit them.
    • Got started on the modification to make these splash plates fit over the long weekend. First the surprisingly time consuming task of swapping all the cam cap bolts to Tomei cam cap studs. I did the method of removing one bolt at a time, applying loctite to the stud, double nutting to torque as the manual described. Then carefully unlocking the nuts without disrupting the torque of the stud (and going back to re-torque a few times when it slipped). Finally applying the nut and torquing to spec. Repeat x28 Next up I went about removing the stock cam cover baffle so I could ensure it was fully clean after drilling for stud clearance.  As the blind rivets holding the baffle on were domed I used a punch to mark the center then used 4mm drill bit to carefully drill out the rivet without going too far part the baffle. As seen in other thread here is what is inside the stock baffles I decided on M4x6mm bolts to bolt the baffle plate back on with. I used a 3.3mm drill bit with some tape to mark the depth at ~8mm. Next was to tap the threads using a cheap bunnings kit M4x0.7. With the baffle removed I also drilled out the spot welds holding in the baffle plate oil returns. Unsure whether this was the best option or if I should have cut holes in the Hypertune splash plates to allow the oil drains to still function... time will tell. I then removed the the Hypertune splash plates so I could rest the cam cover on top and use a dab of grease to mark where the studs impacted the oem cam cover baffle. The most obvious spot was on the hump from the stock mesh is held. Using this hole as an anchor I bolted the oem baffle plate back into the cam cover and lined up the Hypertune splash plate. Marked the rest of the holes for the studs and drill those out too. Total 32 holes drilled and 12 threads tapped on the passenger side cam cover alone for this bolt on part that totally clears all OEM cam covers.. Drivers side next as well as some E85 safe fuel foam to fill the space behind the behind cam cover baffle plates. oh and some lock nuts for the splash plates of course.
×
×
  • Create New...