Jump to content
SAU Community

Recommended Posts

my old R33 GTS-T had misfiring issues from day one... could not even cope with 180rwkw... Splitfires were the fix for it...

my current car R33 GTR is now putting out 270kw at the wheels with the standard coilpacks... no spark issues at all

"if it aint broke, dont fix it"

There is a shortage of hard evidence on coilpacks.

The stockers have the track record.

Splitfires are getting a track record over a few years now.

I have bought a set of Yellowjackets on the basis of bench tests i have seen but they still have to prove the lasting qualities.

The red ones appear to be lesser quality but again time will tell.

I had a similar issue ~ 18psi (250rwkw mark) and the new coil packs resolved the problem.

Running 18psi initially was ok on the original coil packs, replaced spark plugs, tried the silicone coating which helped slightly but the misfire came back.

Ended up buying the yellow jackets and the problem has gone. When I get new spark plugs I'll buy the ones gapped at 1.1mm (against 0.8mm) now and see if the spark still holds.

Last post in here covered it

http://www.skylinesaustralia.com/forums/Gc...20&start=20

Edited by benl1981

Well I dunno what your car setup is, but usually when a person runs an atmo bov on a stock ECU it will run a bit richer on gear change and cause a bit of a pop/backfire through the exhaust.

whats the silicone method? smear house grade silicone around what part of the coil? what are the first signs of missfire on a 25det with only breathing mods that runs std boost?

first signs of a missfire would probably be the missfiring, under max boost between 3-5k rpm, or randomly cutting out and having popping sounds like a wrx until you either turn the engine off or it fixes itself. ive had both.

i was trying to find the coilpack silicon-ing diy but didnt manage it, same principle as these

http://www.skylinesaustralia.com/forums/Fi...=coilpack+clean

http://www.skylinesaustralia.com/forums/Mi...500-t32356.html

Edited by Galois

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Gday, Due to not finding much up to date info on this topic I thought I'd make a thread to get peoples latest opinions/recommendations. Background info -  I've got a S1.5 R33 GTST as a fun project car, mainly for street use and occasional drag strip, apart from all the cosmetic things I'll be doing a full rebuild of the engine with forged internals. Since it'll be getting new cams (kelford) and springs to match I thought I might as well get new lifters and valves while I'm at it, the dash says 160k KMs but the engine seems pretty tired, compression measures about 130psi across all cylinders so I'd like to freshen everything up. This is where I'm tempted to just fork out the extra and go solid lifters while it's all apart, aiming for 400-450kw atw with a flex tune. Assuming all supporting mods (oiling, fuel and all bolt ons) with a lightly ported head and turbo to match (yet to make a decision possibly gtx3582r or similar from Hypergear) I've seen the Tomei kits with just the buckets getting around, Supertech sells most things - Supertech High Performance Cam Followers | Trusted Racing Cam Followers Questions -  Has anyone found the Hydraulic lifters to limit them at this power level? Is it usually found that you can just clean the stock lifters and find they work fine?  Does going solid lifters save any headaches/issues with hydraulic lifters in the future? Any recommendations on other things that will need to be replaced, I know I'll need to get the solid profile cams but can you use the same type of valves and springs/retainers and is it recommended to change the guides and stem seals?    Summary -  Basically looking for pros/cons and wanna know if I'll actually need the extra RPMs from solid lifters or it'll just be bragging rights to say it ReVs OvEr 8000 Cheers
    • Ha ha ha, this stuff they had was installing Toshiba PLCs that were made some time in the 1990s, and they were replacing GEM80 PLCs. To let those two talk (staged upgrade along a ~1.2km long building that was split into 4 sections), was a bunch of WinXP machines running Java gateways... There was no way to put something like ProfiSafe in... Most of the HMI machines were WinXP, with Java program, with a custom button board emulating a keyboard... About the only buttons in the operator stations that went direct to the PLCs was the eStop. There was some interesting design stuff in that place...
    • Stock bypass valves are good for plenty of boost.
    • Check for fuel flow out of the outlet end of the rail. Check for spark. Try to start with aerostart (or pressure can brake cleaner or similar solvent in a car) prayed in through TB. If you have fuel and you have spark and it will fire on substitute fuel, then seriously suspect that E85 sitting for ages in your fuel system has destroyed something and put it in your injectors.
    • Nissan stock oil pressure is typically about 1 bar at 1000 rpm plus about 1 bar per thousand revs on top.
×
×
  • Create New...