Jump to content
SAU Community

Blitz Today?

MUZT3K

By MUZT3K,
in Victoria

 Share

Recommended Posts

WYTSKY Veteran

WYTSKY

Posted
Posted

Also noticed a heap of cops today around the doncaster/templestoe area when I was going to a client - 4 in 15 minutes. I didnt have time to take a snap, but I saw with my own two eyes an undercover brand new xr8 that pulled someone over down the end of springvale road, towards templestoe way.It didnt have any extra aerials and I couldnt even tell until I saw the two tiny red and blue lights flashing.

adznight Newbie

adznight

Posted
Posted
  GTTR34 said:
there's nothing wrong with cruising with your friends on a friday or whatever night... some people prefer just hanging out, cruising, going for a meal, etc rather than hitting up a nightclub :blink:

there's a big difference in meeting up with friends socially, to being a dickhead who goes to princes hwy purposely looking for runs.

Yup, ppl forget this mate. It's enjoyable driving a nice car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin 路 Posted

      There are a few different ways of doing it. I'm currently running two 1000cc pre-TB nozzles and PWM the pump for control. I'll be moving over to a constant pressure system and direct port. I'll run the pump off a regular relay, have it cycle on roughly 5psi before I start injecting to build pressure and then PWM a WMI solenoid (It's basically an injector that can take a lot of pressure and not corrode with water and meth.) The solenoid feeds the 6 direct port ~200cc nozzles. I'll also keep one ~250cc pre-TB nozzle to help keep IAT's in check.  Safety will be a little different as well. I used to use a pressure switch but will be moving over to a pressure sensor between my solenoid and nozzles. I'll trigger my solenoid and if I don't see specific pressure within a specific timeframe (e.g 100psi within a second, 175psi within 2 seconds), I kill it and revert back to non WMI maps the same way I did it before with 4D in Haltech. I was just figuring out the timers in my ecu last night. They made that a little more complicated than I would have liked... I wish Haltech offered a larger set of logic/math functions like other ecu's do. I can't do very much with just AND's and OR's.  I've been asked to do fuel/ignition mapping on a medium bore engine at work in May (192L V16). Being the only programmer in my region and having went and opened my mouth about knowing the ins and outs of fuel/ignition mapping, I have now been deemed an expert. Fun fun. The entirety of the logic and algorithms are programmed in C on a PLC. As I spend more time figuring it all out, I like what I see and eventually I may consider doing the same as a pet project to replace my ecu.   
    • Dose Pipe Sutututu
      R32 GTST - 600KW+ RB28/CD009 Build

      By Dose Pipe Sutututu 路 Posted

      This would be interesting, would you feed it via a 2nd row of injectors? Or just usual WMI nozzles?
    • Milkmun
      Magnetic Drain Plug Snapped in Half

      By Milkmun 路 Posted

      Cut sump up and extend. Win win 馃槀 
    • SLVRBAKSLPZ
      Recommended Torque: RB26/30 ARP 1/2 Head Studs

      By SLVRBAKSLPZ 路 Posted

      All, What's the recommended torque for the 1/2 head studs for RB30 twin cam conversion with RB26 head?  
    • Duncan
      Magnetic Drain Plug Snapped in Half

      By Duncan 路 Posted

      also, we need to know which solution worked....
脳
脳
  • Create New...