Jump to content
SAU Community

Recommended Posts

Spent yesterday on the car, mostly tidying up but got a few things done.

Removed these split HKS dumps ...

CIMG6588_zps017ab2c5.jpg

And replaced with this Midori setup. Biggest off the shelf dumps I could find, and the front pipes are pretty big compared to the JustJap ones I had on previously. Biggest in a two bolt flange.

They have really thought about the design on the Midori's, really easy to get to all the nuts as opposed to the HKS where I needed three different 12mm spanners for the nut at the back of the front dump.

CIMG6586_zps79fb7b2d.jpg

CIMG6584_zps13e12b94.jpg

CIMG6587_zps5ecb3c1f.jpg

Also rebuilt the clutch master with a new piston kit from Nissan. Really simple, two circlips, a good clean and check of the cylinder and back together with new bits.

CIMG6589_zpsf52b75bd.jpg

Comparing pistons easy to see why it was leaking.

CIMG6590_zpsa3f2c5af.jpg

New piston in.

CIMG6591_zps6807fa27.jpg

CIMG6592_zps2efb86bd.jpg

CIMG6595_zps3c3b814a.jpg

CIMG6596_zpsdf88a148.jpg

All back together and on the car.

CIMG6597_zps3f8becd9.jpg

BBQ fired up, triple level bbq burgers with the lot with an integrated egg / toasted bread centre layer and a couple of JD's - golden.

CIMG6599_zps6112f455.jpg

Have a spare full R34 battery cable / tray / fusebox setup so replicating the setup on the R32.

CIMG6604_zpsa8997fc7.jpg

The riser into the engine bay doesn't quite work with the R32 so modified one of the brackets a bit to bolt to the same spot as the speedo cable. Will do some more work around here to make sure its locked down and doesnt interfere with anything else.

CIMG6613_zpscad55a0e.jpg

Rivnuts all the way.

CIMG6614_zps4db55bed.jpg

Shape along the rail is identical. I lined up where the rail tapers out towards the front and the rest falls into place.

CIMG6620_zps5a8578b9.jpg

About the right amount of length up engine bay end.

CIMG6621_zpscd72c65b.jpg

Existing hole in the boot matches the standard R34 grommet.

CIMG6622_zps2c05eef1.jpg

Rear of the rail brackets fit in pretty well here too.

CIMG6624_zpsd05a76cd.jpg

Up over the tailshaft. Bit different here so I may even go direct to the boot and size the cable down accordingly. No need for it to be longer than it needs to be.

CIMG6625_zpsa256d985.jpg

How are you going to sit the positive end of the battery cable in the bay? My 33 has the battery under bonnet and I'm going to be putting in one of those cables like you are, just can't work out how I'm going to sit all the positive ends without it being dodgy or earthing out on the body.

How are you going to sit the positive end of the battery cable in the bay? My 33 has the battery under bonnet and I'm going to be putting in one of those cables like you are, just can't work out how I'm going to sit all the positive ends without it being dodgy or earthing out on the body.

I have the standard fuse / relay / distribution block spare from an R34 GTR so I am going to try to use that instead of the standard R32 GTR one you can see in the pics at the moment.

  • 2 weeks later...
  • 2 weeks later...

Sunk a good chunk of time in yesterday.

Finished off the power steering lines and pump in place.

IMG_0721.jpg

Time to drop the engine in.

IMG_0726.jpg

Triple check the rigging while stand still attached to make sure it holds up while hovering the engine over the car.

IMG_0728.jpg

Engine in!

IMG_0744.jpg

Looking good Paul. Now the fun bit.... the gearbox :D

Haha yeah looking forward to it .... I have a 500kg trolley that should help the cause a bit.

Need to get the flywheel machined first then the shenanigans begin.

  • 2 months later...

Getting things rolling on this again now I have recovered from everything else. Aiming to have it started within about the next 4 weeks.

Sammich plate is on, flywheel sent off for machining yesterday should be back today.

Clutch and gearbox should be back in over the next few days

Flywheel, clutch, gearbox and starter are in.

Freshly machined flywheel fitted and torqued up.

CIMG6758.jpg

Then realised being a new engine it was missing the pilot / spigot bush in the end of the crank.

CIMG6759.jpg

Picked one up and installed and flywheel back on.

CIMG6760.jpg

Clutch on. Its an Xtreme unit I already had in the car, handled ~300rwkw so should still be up to the task.

CIMG6762.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, that was one of the things we learned fast in the past with our MX5. When you drive with the top down, you are effectively standing out in the sun, 100% of the time, and not getting in any shade (because roads aren't shaded generally!). Just like standing out in the middle of a field on a sunny 27C day is a bit of a bad plan, so is sitting in a MX5 without sun protection.
    • I also just ordered some Frankenstein bolts and side mounts to fit a hard top Just in case I do find one, basically so it doesn't need to be fixed to the car with only the front latch.......and then gaffa tape to keep it in place for the RTN journey from wherever I get it
    • If your temps are fine now, you probably won't have any issues with where your vents are as they don't look right up at the windscreens high pressure area, so any differences when giving it the beans for extended happy laps would be minimal, but, they should vent heaps when stuck in traffic  Much like how that reverse cowl on my SS let "visible" heat out when stationary, but, because it was basically at the windscreen my coolant temps on the Hwy actually raised because air was being fed into it at speed (110kph), to only come back down to around 90° when I got off the Hwy And your 100% correct about the NC currently not needing vents, but, if I was to add a turbo, and a oil cooler and intercooler in front of the condenserand radiator, and then take it to the track???? It is apparently a recommend requirement if I don't want to worry about coolant or oil temp issues, but, any of the above are possible scenarios, over time As it sits now, with the triple pass radiator and stock air conditioning system, I have absolutely no issues with either temps or air conditioning efficiency, I've been basically daily driving thie car for the last month, both on the Hwy, and peak hour, bumper to bumper traffic, but, that's pretty much expected from basically a standard engine  Talking about no issues daily driving, it was 39° the other day and I was sitting in bumper to bumper traffic on the M5 and then M7, with the top down, and with the air conditioning blowing nice cold air on my feet, balls, and face, well, there was one issue, my head and arms got pretty sun burnt Note to self: leave a hat and sunscreen in the car for such days 🤣
    • I would agree, unless you need something specific to the HV motor/battery side repaired or investigated, any mechanic will be able to perform normal services, but if you prefer, maybe look for a mechanic who regularly services/repairs Nissans, the VQ engines are pretty common in the Nissan lineup.  Sorry, I can't make any suggestions, I don't live in Vic.
    • Some of them keep working fine. 9 out of 10 of them end up causing an absolute misery bleeding the system and get thrown on the workshop floor in a tantrum and never thought about again because they were never really needed and just added crap to the car that we could have done without. Same-same with HICAS, A-LSD, and various other stupidities that over eager 10x engineers thought we had to have.
×
×
  • Create New...