Jump to content
SAU Community

Recommended Posts

  • Replies 65
  • Created
  • Last Reply

Top Posters In This Topic

Still to go. Price drop

Bonnet $220

lhs front gaurd $100

rhs front gaurd $100

rhs front headlight $100

gaurd orange indicators $20 pair

dash missing two small vents on top $100

center consol $50

heater/aircon control $40

heater $100

rear seats $130

entire floor carpet $100

roof lining $50

center roof light $20

map lights $20

holy shit handles on roof $10

lhs a pillar $20

speedo cluster $100

glovebox $40

rear seatbelts $20

rhs sun visor $20

rear lhs tail light $100

passengers door$150 with all electrics

door linings and electrics can be separated along with mirrors

side skirts (one cracked) $50 pair

windows (remove yourself or get removed properly) $$$

3"catback exhaust with emptied cat and rear cannon $350

interior lining $80

parcel shelf $50

boot lining $50

boot seal $25

bonnet latch $35

horn $15

fuel tank $100

rear skyline strip between lights $60

scuff panels inside doors $25 pair

fuel cap covering panel $20

windscreen wiper stalk $15

indicator stalk $15

steering column $40

front calipers $250 pair

rear rotors and calipers $200

front 5stud hubs $100 pair

rear 5stud hubs $100 pair

standard diff $200

front suspension $100

  • 4 weeks later...
  • 2 weeks later...

Bump

all this needs to go- all offers considered-just taking up room need it gone,

complete rear subframe has been pulled out too.

Bonnet and rear seat no longer available-

rear calipers are stil available-

0419837474.

  • 2 weeks later...
  • 4 weeks later...
  • 2 weeks later...

do you still have the front bar? i need the indicator/driving light section for a series 1, same as 1.5, need those front panel lights!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • FWIW the depth of the groove in the rubber pad is not super essential, the blocks are rubber and squish a bit. If you are worried an angle grinder will make a deeper groove quick smart
    • I mean, if you were to move the jacking points away from the original location, that is, away from the wheels and closer to the centreline of the car, then it will be more likely to overbalance and tip off the supports. Same as we talked about before. I was talking about moving for-aft. If the sill is bent outward or inward, then the car would obviously look unstraight from the outside. Hopefully that hasn't happened either. Again, you can do comparative measurements from the chassis rails to see if there is much deflection.
    • Can you elaborate what you mean with your first sentence? I meant move as in the bulge kinda seemed like it got pulled "outward" meaning it got pulled down and to the side with the jacking rail itself, so the load bearing bulge now sits lower than usual and is not level with the sill on the other side of the jack point. Either that or the jacking rail just got pushed in a good bit.
    • As well as being risky WRT tipping off anyway. Yeah, I wouldn't expect it to move. Just measure from the rear one to the front one on the good side, then measure that same length on the wrecked side. You will find the notches in the pinchweld, and the jacking pad. Just spray a spot of marker paint or something there.
    • but any other area than the bulge you are talking about will just cave in then? The front driver side is pretty bent so I don't know if that will work the way it is now. I can still kinda make out where that bulge is/was but it looks like the position of it also changed due to all the mistreatment? Hard to tell
×
×
  • Create New...