Jump to content
SAU Community

> Rb25 R32. Basic Mods $6750, Top End Just Just Overhauled

vitz_n1
 Share

Recommended Posts

vitz_n1 Community Regular

vitz_n1

Posted
Posted

Im going back overseas in a few weeks so need to sell my car.

So i had this car for sale about 9 months ago but it didn't sell before i left overseas. Im now back for a short period and need to sell it. I had it for sale for $8500 last time and had 3 offers. 2 of $8000 and 1 of $7750.

http://www.skylinesaustralia.com/forums/Rb...50-t294143.html

Its now been sitting in the garage for 9 months being started every 1 - 2 weeks to keep her fresh. So based on this i am fairly firm on this price of $6750 so please no low balling.

Car is a Wine red R32 with RB25 conversion. Motor has 80 000 km on the clock. Chassis has 150 000 from memory... ill have to confirm that. Also has 12 months rego on it.

The good

Recently the tensioner let go and my valves bent. When replacing them i decided to clean up the whole top end to had all manufacturing imperfections clean up on the head. Also has new head gasket and head surfaced, valves and stem seals, tensioner and idler pulley. Also new exhaust and inlet mani gasket..... so head is pretty much as good as new.

Anyway so car has RB25 conversion.

Still has RB20 g/box.

Mods

Buddy club N+ coilovers all round - Awesome suspension BTW, by far the best ive driven on in its price range.

Greddy type m front mount

3" exhaust turbo back

Exedy heavy duty organic clutch

Few things inside, trust gear knob, omori din gauges.

Bosch 040 fuel pump

unknown aftermarket rear camber arms

Rear spoiler off hole filled and resprayed

32 gtr rear wheels

Turbo smart plumback BOV

What i'd suggest doing

Some of these may well get done if i can find time before i go:

Left rear wheel bearing to be replaced... i have bearing unit sitting in my bedroom, just gotta get out the and change over.

Left rear camber to be adjusted more + or right more - as they are uneven and pulls to the left..... so basically needs a wheel alignment.

It is running rather rich on standard ECU and pops and farts a bit on de-acceleration and dumping a bit too much fuel when it comes on boost, so i'd at-least get a piggy back tune.

Has a dint about the size of a 5c coin on the boot lid, not very deep at all. also a chip about 2mm in diameter on rear quater panel also another small dint on roof. Other than that body is straight.

*** Please note *** I have had the engineering check done for the car and paid half of the fee ($250) there are a couple of small things required for the cert plus the remaining $250. I would allow $1000 to have the car engineered. If you can do mechanical work yourself then maybe a little less. That also includes the cost of the certificate.

So thats all i can think of at the moment. I've tried to explain everything i can think of.

Honestly, this car has been very well looked after. Its rarely driven and serviced regularly with mobil 1.

Id really love to spend a month or so getting it to where i want for sale but i simply dont have time.

Price is $6750.

Located in east burbs of Melbourne

When i can get these photos to upload i will... not working atm for some reason.

vitz_n1 Community Regular

vitz_n1

Posted
  • Author
Posted

The biggest pain for eng cert is it needs side intrusion bars for the doors. I'm looking around for some now. I was just gonna put some on, get the cert, swap them back then re-sell the doors.

Anyway so side intrusion bars, side indicators, tyre placard, baby restraint, noise level test.

For RWC it will be fine. Ride height is actually legal. The exhaust tucks up nice, looks a lower than it is.

I guess wheel bearing would need to be done.

StuC Enthusiast

StuC

Posted
Posted

so the car has never been complianced in Australia then as it should have had side intrusions put in and baby restraint fitted to get into the country under either RAWS, SEVS or 15 year rule.

vitz_n1 Community Regular

vitz_n1

Posted
  • Author
Posted (edited)

I thought that may have been the next question. Sorry should have cleared that up in previous post.

The previous owner used this as a track car. He changed the doors to ones without side intrusion for weight reduction. Also had interior stripped etc...

So i bought it with RB20 and replaced all the interior and bits he had taken off.... besides the doors. At that stage i wasn't thinking of doing the conversion, nor did i realise it was necessary for engineering.

As for the child restraints....i dont know...maybe he thought it looked a bit silly and took it off... i probably would have done the same :down:

Also, yes it is running standard R33 ECU.

If anyone needs re-assurance i can take a photo of the cpmpliance plates on the car and post them up.

Edited by vitz_n1
vitz_n1 Community Regular

vitz_n1

Posted
  • Author
Posted

**Update** Just serviced her today. New oil and filter, tran fluid, spark plugs, checked timing and compression.

Compression results were 158 158 161 156 160 158, that was with throttle closed, so i was very pleased with these results.

With the timing belt, tensioner, idler pulley, head gasket, exhaust and inlet gasket, valves and seals all replaced she sure is nice and fresh.

Running beautifully!

Also put a new battery and reco'd alternator in as the batt light was starting to come on intermittently and battery draining. All fixed now.

Tyre placard is now done and i bought the side indicators, ill try fond time to wire them up tomorrow.

vitz_n1 Community Regular

vitz_n1

Posted
  • Author
Posted

Thanks mate.

I thought the price was cheap as well. I had heaps more interest 9 months ago when the I was asking $1250 more.

Possibly the price is leading people to believe the car is in bad condition or something wrong with it. I can assure everyone this is not the case and i just need to sell her!

Ripp3r Mentor

Ripp3r

Posted
Posted

does look very clean..

JiN_MaN: think regency would believe you if you swapped the doors with black 32doors that have intrusion bars? and say you bought it like that ect

JiN_MaN Veteran

JiN_MaN

Posted
Posted (edited)

What makes you think it doesn't already have them?

*vitz_n1* Hope you dont mind, at least we are keeping your thread at the top

Edited by JiN_MaN

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
×
×
  • Create New...