Jump to content
SAU Community

Massive Clean Out

zebra
 Share

Recommended Posts

zebra Grand Master

zebra

Posted
Posted

Guys Im cleaning out my Garage's

So offloading all the un-needed bits cheap

Item #1 - R33 RB25DET Block, Needs a Rebore, comes with Girdle, but no bolts or accesories - $50 pick up only from South Canberra.

Item #2 - Rb25DET Crank Shaft Standard size journels, micro polished - $100 pick up only

Item #3 - Rb25DET Crank, Needs grinding, already done 10thou on mains and 25thou on Rod journals - $40 Pick up

Item #4 used Stainless High mount t3 manifold, used for a few months, suit 38mm 2 bolt Tial Gate, No cracks - $75 + post

#5 - 38mm Tial Copy gate used for a few months $50 plus post

#6 - RB25det factory Upper Plenum, No throttle body or gasket - $40 plus post

#7 - Standard AFM, Still works but a bit sad looking, good for a spare - $20 plus post.

There is heaps more to come

Ill get photos ASAP

Best to contact me via PM or reply here.

Thanks

Andrew

Link to comment
Share on other sites
zebra Grand Master

zebra

Posted
  • Author
Posted

Just thought of some more,

3" Mild Steel Cat Back Exhaust Suits R33 2 Door, Single Oval Muffler at the rear, Ok Condition, Cat is welded to the pipe, but the insides have fallen out, The muffler is around 18 -24 months old, the rest is around 4-5years. - $50, please note the exhaust is in Goulburn NSW would prefer pick up from there.

Used Rb30 Oil Pump, No idea on condition, came out of an RB25/30 which munched the bearings - $20 plus post

5 Rb25det factory Conrods and 6 ACL Race series Forged Pistons, The 5 rods are usable and 3 maybe 4 pistons are. Pistons are 86.5mm and 8.5:1 Comp. - $50 for the lot

Turbo Smart Boost Tee - Not very old, Came with the Soarer I bought - $50 posted.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Stivo
      R32 goes out in right curves

      By Stivo · Posted

      That's true. However, this problem has started since the tuning. First time with the return journey from the tuning. But yes, the pipe was clogged with dirt and rust. That was certainly due to age
    • Dose Pipe Sutututu
      CD009 RB Conversion

      By Dose Pipe Sutututu · Posted

      Great info @tidi0x  Will definitely be handy for others and maybe me if I decide to keep the shit box H pattern.
    • tidi0x
      CD009 RB Conversion

      By tidi0x · Posted

      Bumping this up one last time.... I wanted to follow up on the clutch slave issue. I realized that what the issue comes down to is the pocket is flat milled, and the cylinder does not want rest flat. So in order to mount it correctly you will need to make a spacer for the fingers so the cylinder is floating. I took two plates of aluminum, drilled some holes and was good. I did still need to make the relief cuts in the bell housing, as even with the spacer the bleed section still interferes. The OE bell housing the mounting holes are raised from the housing.       
    • robbo_rb180
      R32 Gtst - Track Car

      By robbo_rb180 · Posted

      If the event in USA goes ahead will be interesting as it seems the rules will get more cars over here. Apparently the track is laguna seca too. Yeah s15, if I get a the lower dash trims, centre console and change front cross member to standard LCA position will fit clubsprint. See how rules are as i would rather do complete widebody than a bolt on flare to run the 295 with proper clearance.
    • 180 wanabe
      370gt Stock Suspension

      By 180 wanabe · Posted

      If the car is legal height I can't see it being an issue. Found a thread on reddit that might offer some insight.   I got a ticket from a copper in QLD for my S15 being too low. They had this wheel thing on a stick that they put under the car and it hit my exhaust. Anyhow went to an exhaust shop to get the exhaust tucked up/hung a little higher and I wound the coilovers up a smidge. Don't think I even had to go back to the police station unlike when I got defected for having a carbon bonnet when I brought the S15 from the ACT to QLD and had to replace it and then rock up at a police station and have a yougish female officer who knew nothing about cars confirm that I had changed bonnets. Should have just painted the carbon bonnet yellow to match the rest of the car lol
×
×
  • Create New...