Jump to content
SAU Community

How Many Km's Have You Got On Your Rb Motor

Josh_r32
 Share

Recommended Posts

greensa14 Collaborator

greensa14

Posted
Posted

My SR has done 170K. No signs of slowing (190RWKW)

My old RB30e had done over 350k with years of abuse all day everyday. Those things are nuclear proof.

If we had a Nuclear war after everything has settled, all that would be left is RB30 blocks scattered around the planet!!

cactus Collaborator

cactus

Posted
Posted
99 R34

3rd owner and legit 44000 K's. It's almost brand spankin new

My old RB20 red-top (which daily saw 9000rpm) had done just over 200,000kms and was running 250rwhp. Was still happy as larry when I replaced it.

Humbla Grand Master

Humbla

Posted
Posted

My rb25 had done 262000 no oil leaks no oil burning,16lbs of boost daily for 5 years.Then some dumb &&&&,changed the sparkys while i was standing beside her,never checked for brocken porcelin off plugs.Put every thing back to gether turned on the 33 bye bye moter,horrible noise.Will add no cost to me. :D

GTR-N1 Grand Master

GTR-N1

Posted
Posted
My rb25 had done 262000 no oil leaks no oil burning,16lbs of boost daily for 5 years.Then some dumb &&&&,changed the sparkys while i was standing beside her,never checked for brocken porcelin off plugs.Put every thing back to gether turned on the 33 bye bye moter,horrible noise.Will add no cost to me. :)

...and you don't even drive like a granny! :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      R32gtr sputtering and stalling

      By joshuaho96 · Posted

      I'm aware, but unless you're actually seeing the voltage the ECU is seeing and you're able to verify the sensors are actually working I find it hard to just trust STFT/LTFT. I will say, logging the ECU comes naturally to me because it's one of the lowest effort methods of diagnosis and I do similar things in my day job all the time. Staring at 20+ charts looking for something that isn't quite right isn't for everyone. NDS1 allows you to log almost everything so that's normally what I do and then sort out the data later. 
    • MBS206
      Neil's R33 Gts-t Build

      By MBS206 · Posted

      Silly question, as I bet you've checked already, but the motor turns over by hand yes? I suspect Neil has a spare starter, though if not, I believe I have a spare R33 (or two) starter.
    • Duncan
      NPboosted manifold fitting purpose

      By Duncan · Posted

      Yeah just run one of those posts to the Link like GTSBoy said. From google it looks like a "mishimoto boost controller" is a manual boost controller. Since you already have the link just buy any MAC valve and plumb it in where the mishimoto is now. Wires to the solenoid should come from the Link's / standard loom boost control wiring (I guess you have an r32, not sure if it is gtst or gtr, if it is GTR where is a 2 pin connector near the engine bay fuse box/injector resistor for that purpose, assuming the standard boost controller is gone)  
    • GTSBoy
      NPboosted manifold fitting purpose

      By GTSBoy · Posted

      No. The ECU's hose is for a connetcion between the plenum (assuming single throttle body, not ITBs) and the ECU's internal MAP sensor. This is the primary load measurement of the ECU - so you need to get this one right. This has NOTHING to do with the boost contol. The wastegate also needs to see a boost signal - but it is actually far better for it NOT TO COME FROM THE PLENUM (again, assuming single TB, and not ITBs). This should come from the turbo's compressor housing (assuming there is a nipple on there, which there might well not be), or on the boost pipe somewhere between the turbo and the TB. On the pipe from the turbo to the intercooler is usually most convenient. The boost controller is then located between that boost source and the wastegate, ACCORDING TO THE CORRECT PLUMBING DRAWING FOR THAT BOOST CONTROLLER. There is no general diagram or instruction that will be correct for every case. Then the other ports on the plenum are for purposes such as Duncan described. If the boost controller has an internal MAP sensor, for a boost display, etc, then it will want to be hooked up there, alongside the ECU and the FPR.
    • eli995
      NPboosted manifold fitting purpose

      By eli995 · Posted

      Ok gotcha, so one post to fpr  another to bov  and I have the mishimoto boost controller and a link g4+ so I’d just have the tuner set it up properly. For the last two from plenum post throttle to  ecu/ boost controller, I know that I have a hose coming from the ecu that I was confused about so I assume that’s what connect to the boost controller from the ecu? And then the last is just from plenum to boost controller then to wastegate?
×
×
  • Create New...