Jump to content
SAU Community

Recommended Posts

Selling my car as I've recently started a new job and I rarely use my car anymore. I did have a thread up for my car before, but being busy with work and personal issues did not continue with the sale of my car and I guess the thread disappeared.

Here are the cars specs:

- Black 1993 Series 1 GTS25

- 5 speed manual

- Chassis and engine has done 16X,XXX KM (Odometer was changed prior to me purchasing the car as the dials on the old cluster were not functioning)

- Rego until Feb 2011

- Full 2.5" exhaust throughout installed by Bankstown Muffler Fit

- New Century Battery installed

- Harmonic balancer and key crank replaced/repaired

- Lowered suspension

- 18" 2 piece rims

- Aftermarket alarm system and immobiliser

- Momo steering wheel

- Automatic Climate Control

- Paint is in average condition. Clear coat peeling on spoiler and driver side front guard.

Note:

- Hit and run has damaged the current front bar and reo. I do have a spare front bar for the buyer to use, however it is in a two tone grey colour and will need to be resprayed. Headlights and indicators haven't been touched and radiator support is straight.

- Dent on rear quarter panel (existing damage from previous owner)

- Driver side window does not work, will need a new regulator (roughly $100). Passenger side window works fine

- Central locking will not unlock the doors using the remote. Alarm however is still in perfect working order and immobiliser works 100%

Pictures:

th_6.jpg th_1-1.jpg th_2-1.jpg th_3.jpg th_4.jpg th_5.jpg th_7.jpg th_8.jpg

Price:

4.5k with rego ono

The car runs smoothly and hasn't missed a beat since the repairs and I have the receipts for most of the work done to the car. The exhaust has a nice deep rumble for an N/A car and doesn't attract too much attention.

Contact:

Via PM or call/sms 0431 737 515

Link to comment
https://www.sau.com.au/forums/topic/331105-r33-series-1-gts25/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have one and it was at ~43.5PSI.
    • Put a pressure gauge on the fuel rail.
    • I've uploaded logs / the current map to Gdrive if anyone has any ideas. https://drive.google.com/drive/folders/1FPnr22Z-EilG7tYdHSi0Qb07P2jfFLKV?usp=sharing
    • I'm running a Haltech Platinum Pro with the stock map for the RB20DET + tweaks for my build. When I started it this morning, the IAT was at 32F/0C (Outside temp was ~42F) and the AFRs went off the scale for my AEM gauge. I let it run for ~30 seconds then turned it off. I then did a smoke test, by hooking into a vacuum line directly behind the throttle body, and confirmed there was no leaks ( i let the smoke tester run for ~5 minutes / confirmed it was generating smoke before hand ). I then started the car again, after fixing a power steering leak.... and it seemed to be happy for ~30 seconds (was at ~11/12), but then seemingly shot back up to ~18 again. I then let the car run for a few minutes, thinking this was just cold start related, but the AFRs never came back down. I didn't let the car fully warm up, so maybe this makes sense, but I'm not sure what to do? The AFRs, when I last ran it, were normal, but because of personal reasons I haven't been able to break in the car. It was rebuilt last year. Engine / Mod list: Supertec pistons Spool rods Kelford 270 cams and Springs Stock crank Deatschwerks 900cc injectors Walbro 255 (Wired directly to the battery relocated in the trunk) NKG Audi R8 Coil packs + Conversion Harnesses from Wiring Specialties Holset HY35 turbo Haltech Platinum Pro ECU Haltech boost controller (wired in for high boost RB25 Neo transmission + needed bits for the speedo to work  
×
×
  • Create New...