Jump to content
SAU Community

Recommended Posts

Hi there

I am after some info on the apexi safc, like how much more power would u get out of using one and can u tune the car that much more with one with standard ecu. Sorry for my ignorance I dont understand them that much. I have the following mods if that helps.

Nissan Skyline1997 r33 s2

apexi airfilter

walbro fuel pump

large front mount

dump 3in exhaust

splitfire coilpacks

atomic boost controller running 10psi

bov

with standard turbo

thanks

Link to comment
https://www.sau.com.au/forums/topic/331866-apexi-safc/
Share on other sites

not sure how much power you have now but with a SAFC you can tune the air/fuel and net 250-280rwhp

aorund 200 now? assuming you dont hit R&R

but if you plan for more mods in the future then get a stand alone ecu which can control ignition timing would be better

Link to comment
https://www.sau.com.au/forums/topic/331866-apexi-safc/#findComment-5384682
Share on other sites

Hi there

I am after some info on the apexi safc, like how much more power would u get out of using one and can u tune the car that much more with one with standard ecu. Sorry for my ignorance I dont understand them that much. I have the following mods if that helps.

Nissan Skyline1997 r33 s2

apexi airfilter

walbro fuel pump

large front mount

dump 3in exhaust

splitfire coilpacks

atomic boost controller running 10psi

bov

with standard turbo

thanks

Most cars with those mods will get between 180 to 200rwkws.

I got similar mods on my car minus the FMIC (only got a SMIC off a 34 GTT) & the coil packs (still on stock ones I think), I got 180rwkw when I got my SAFC 2 tuned at All star garage.

Also my car is a 4 speed slug auto box so theres more power loss at the transmission compared to manual.

Link to comment
https://www.sau.com.au/forums/topic/331866-apexi-safc/#findComment-5384734
Share on other sites

i reckon something like a Nistune/Mines/Blitz tuned computer coupled with a SAFC is bomb, that way you have the more agro timing maps, and can still pull/put fuel where you need it!!!

why do you need safc when you have nistune?

Mines/Blitz are tuned in jap land and i dont think their suitable with aussie conditions

Link to comment
https://www.sau.com.au/forums/topic/331866-apexi-safc/#findComment-5385064
Share on other sites

Hi there

I am after some info on the apexi safc, like how much more power would u get out of using one and can u tune the car that much more with one with standard ecu. Sorry for my ignorance I dont understand them that much. I have the following mods if that helps.

Nissan Skyline1997 r33 s2

apexi airfilter

walbro fuel pump

large front mount

dump 3in exhaust

splitfire coilpacks

atomic boost controller running 10psi

bov

with standard turbo

thanks

I used to have an Apexi SAFC and an SITC (to control timing) and they worked reasonably well but I would recommend a Nistune chip which will give you much better tuning ability for about the same money. Nistune do not make a chip for the R33 so you will have to use an R32 ecu or other and chip that. Do some searching - there have been a few threads on this topic.
Link to comment
https://www.sau.com.au/forums/topic/331866-apexi-safc/#findComment-5386329
Share on other sites

If you are ABSOLUTELY sure u are not going to do any more mods except raise the boost 1-2psi the safc will be the cheapest and best bet.

U may just get a few extra max kw but the good part is that you can tune out R&R with it and make the mid range come to life

I had an safc2 along with an adj fuel pressure reg and the exact same mods listed above on my 25 and the car felt so much better to drive without that hole in the mid range

Link to comment
https://www.sau.com.au/forums/topic/331866-apexi-safc/#findComment-5386372
Share on other sites

True that ^

But then again it seems pointless. A Nistune board will cost much the same as a SAFC, perhaps a little bit more considering you need the R32 Or Z32 board for an R33. You need a tune on the Nistune or the SAFC, Nistune will be cheaper to tune because it will already have a base image for your car. And then the gains you will get from the Nistune far outweigh those of a SAFC...

Link to comment
https://www.sau.com.au/forums/topic/331866-apexi-safc/#findComment-5386539
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that.... If only I could do something once and be happy with that, like some people do....
    • I had no transmission at all so I managed to find a big box manual gearbox from an R34 GTT for an insanely good price in EU. I converted it to push type which cost more than the transmission almost, with parts from Amayama! These engines are very strong and can put out decent power with a properly sized turbo. You can save on money from parts like pistons and rods, and invest those in the transmission and other parts. I suggest you join the RB20 Enthusiasts facebook group, plenty of info and almost daily posts there about 20DE/DET/Neo+T builds. (I hope I'm not breaking any forum rules by mentioning third party platforms, just trying to help the buddy out)
    • Yeah, having tried all of those methods including BBQ+recipro/hacksaw, I ended up buying a bush press kit under $150 that works well, like this: https://www.ebay.com.au/itm/355967727167?mkcid=16&mkevt=1&mkrid=705-154756-20017-0&ssspo=sfmmuhxgqhm&sssrc=2047675&ssuid=dJvnaZ11TB-&widget_ver=artemis&media=COPY It basically has a range of pushers and cups with threaded rods between to press out a range of large bushes. The problem with any sawing solution is minimising damage to the subframe side, although it probably needs a quick sand afterwards no matter what solution you try due to damage
    • Hi. Thanks for the answer. I do not have instagram 😄 I too considering turbo the RB20DE NEO 🙂 But i think i upgrade the gearbox first or at least buy new.  
    • Just pulled the passenger apart so got a good idea, also the side bracket that pivots the top half is completely cooked.. how I don’t know.. haha and paid $400 also included a photo of the passenger seat! She is mint
×
×
  • Create New...