Jump to content
SAU Community

Recommended Posts

Hey guys i have a R33 GTST with the usaul mods only recently the car is struggling to crank like its very weak and stuff during start up, then if i leave it a day or two it won't start. All the dash lights/head lights etc turn on just when i try to crank it i just hear the fuel pump priming and there is no cranking sounds when i try to crank it....so im just wondering has my starter motor died or is it something else?

Cheers

Chi

Link to comment
https://www.sau.com.au/forums/topic/331966-desparately-need-help/
Share on other sites

Battery, alternator or starter. Sounds like the former.

Your starter needs a lot of power to crank your engine over, sometimes there will be enough charge to power the fuel pump and dash lights, but then not enough to crank the engine.

Charge it or get a new battery...

mmm so you don't reckon its the starter motor? il put the bolts back on the starter motor tm morning and change a new battery over....alternator is quiet new got that done like last year. cause i thought if it was the battery it would go tick tick tick tick

If it was your alternator your battery light would come on as you were driving as eventually there would be no charge in your battery, if it was your starter motor after you gave the starter motor full voltage it still struggles to crank or what it sounds like is your battery can't hold charge anymore.

Could also be some other small things a lot of people over look, like a poor earthing on your battery.

Id tip its your battery, if it was your starter motor leaving the car alone for a few days isnt gona effect it but I say your battery not holding charge if your not getting clicking that just means the batteries really dead. Try with a jump starter if starts easy then its your battery.

turn headlights on and then try and crank it. see if they dim.

if you can get access to the starter motor u will see where there is the main nut that the power goes too and then the little electrical tab that the start signal goes too. take the little start signal wire off and check with a test light to see if the wiring is getting power when the key is turned to crank, if not than there is a wiring issue.

while your at the starter motor get a screwdriver and short the main power terminal with the start signal tab, do this carefully and only touch it quickly then take it off, this should make the starter kick in and crank the engine, this will tell you the starter is ok.

let me know

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How's your first born doing? 😛 As for now what? Time to forget about it for 12 to 18 months while your go down a totally unrelated rabbit hole... 😛
    • Fuse taps are perfectly fine to use, especially when you're adding stuff for your own car, and so long as you're being smart about it. IE, don't throw a 30amp circuit, onto a circuit that is only a small circuit. It's best to add a small circuit, to one that is already quite large. Oh, and make sure you're not going to blow the fuses that are further upstream too! I dislike their use in other applications, such as alarms, telematics/tracking devices etc, as it's far too easy for someone to unplug them and render a system useless. Those sorts of devices I go for wiring in quite secretively.
    • Fob is all cleaned up and it’s working well!! The amount of Vegemite looking sh*t that was in there is mind blowing 
    • Given it is temporary, I bought a  cheapy gauge mount (which has become enflattened) which I will screw into the existing phone mount Also a first for me; given this is a temporary install I could not think of any reason not to use one of those "add a fuse" thingies to source the battery and IGN power. I had always figured they were pretty dodgy but having a good look at them I think they are a valid option for sourcing power from an existing source without cutting 
    • Finally for now, a bit more work on the transmission temp gauge. I was wondering how Raceworks do a gauge for $100 that autometer want $500 for. No idea about the accuracy of course, but they have cut a few corners that made things hard.  First one I mentioned above, the sender is physically difficult to fit and doesn't work with their own adapters (the extra fittings I used to get the sender into a hose cost more than the whole gauge, lucky I had stuff in the shed) Second, the temp sender wires are way too short. They are shown as 2.7m on the box and I know my routing was long from navigator headlight to driver's firewall back to centre console, but I had to lengthen them by about 2m total - 2 joins in each wire. Also, same with the supplied power loom, they needed about an extra 1m to get the fuse box where I sourced power. Another join in each wire since one end wasn't supplied terminated. I know they could argue that the wires might be long enough depending on situation, but when you consider parts and particularly labour, it would be a very expensive cheap gauge if you can't do the work yourself. And, only a small issue....but it would have been nice if they remembered to tap a tread onto *both* spacers they supplied for the bracket....I haven't had to use the M4 tap often!
×
×
  • Create New...