Jump to content
SAU Community

Major Help And Info For Vehicle Registration

elrodeo666
 Share

Recommended Posts

elrodeo666 Mentor

elrodeo666

Posted
Posted

Hi as some of you may know I have brought my car over from Japan as private import.

heres the thread http://www.skylinesaustralia.com/forums/Hk...il-t246240.html

Anyway the car has been complied and now needs the roadworthy and heres the hurdle and where help and advice is needed...

Ok as its a new N1 block there was no engine number stamped into in Japan thus I need to get one before I can get a roadworthy certificate.

I just spoke to the Dept of transport in QLd and they have said I need to bring it to the RTA Qld to be inspected so they can issue a new engine number and then have it stamped onto the engine, somwehere they can access.

So my dilemma is does anyone know how full on will they check the car as its fairly modified , or is this just a quick gander and they see theres no engine number , issue a new number and then the onus is on me to have it to roadworthy condition.

Or is it a thorough inspection and I'm screwed and up for bucket load of coin to get it on the road.

Is there anyway around all this ??

Any help,ideas and advice would be greatly appreciated and if need be pm

Thanks in advance.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RB25inside
      Compatible rear drive shafts R34 N/A?

      By RB25inside · Posted

      Are these the Dmax ones you are in reference too? https://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35#description Not a bad idea to get the uni flange ones. I have sent just jap an email too. Will see what they say lmao. Only thing is the Dmax ones are on a big back order. Low key anything will be better then my OEM ones I got as they are sounding like popcorn when I go under load lmao 😂☠️🪦.
    • GTSBoy
      Compatible rear drive shafts R34 N/A?

      By GTSBoy · Posted

      They should do. I have S14 (or something S chassis, anyway) driveshafts in my R32 (because my diff flanges have 3x2). They're the right length. When you go looking for R32/3/4 driveshafts (for turbos), they're all the same thing, so are the same length. So there really shouldn't be any reason why those cheapies from JJ won't also fit an R34. R32/3 NA should also be the same thing. The (3x the price) D-Max ones are uni-fit. They have 5x1 and 3x2 bolt holes and say they cover all the cars. So that would also suggest that they are all the same except for the flanges. And in that case, the flange goes both ways. I'd be buying the D-Max ones if I ever have to replace a shaft. Because that will open up diff options without needing to juggle shafts also. Juggling shafts is gay.
    • ChoppedSpots
      GReddy Injector Help!

      By ChoppedSpots · Posted

      Yeah with the adaptors they do look like the photo above - just the fitment within the plenum itself and then further with the rail to the intake is questionable - we shall see tomorrow hopefully once I get some replies from Aeroflow, maybe those bosses are the missing piece....
    • Dose Pipe Sutututu
      GReddy Injector Help!

      By Dose Pipe Sutututu · Posted

      Should be fine, if you have it sitting too far in, you end up just spraying the walls and have shit idle. You "can" run them like that, however I don't think it's a great idea (also depends on your plenum, might be good to just get the injector bosses first, mock it up and see if you need to get the bottom extension) Ideally your injectors, with the extension should look like this  (Not my photos, just Google)
    • ChoppedSpots
      GReddy Injector Help!

      By ChoppedSpots · Posted

      Thanks for the replies guys, it's really appreciated.  It seems the kit was supposed to come with those injector bosses but hasn't. Unsure if they'll help as even with the adaptors to make them a 3/4 height injector they still sit too far out so mount the fuel rail?
×
×
  • Create New...