Jump to content
SAU Community

Holinger Sequential

T04GTR
 Share

Recommended Posts

T04GTR Grand Master

T04GTR

Posted
Posted

hi all, i was just wondering, is there a standard set of ratios for the 6 speed holinger sequential for the gtr?

what seems to be the commonly chosen ones? 6th being overdrive.

cheers

also, does anyone know what the mainshaft to countershaft distance is on the seq holinger?

ie. the os88 is 88mm....

Link to comment
https://www.sau.com.au/forums/topic/332939-holinger-sequential/
Share on other sites
fun123 Rookie

fun123

Posted
Posted
hi all, i was just wondering, is there a standard set of ratios for the 6 speed holinger sequential for the gtr?

what seems to be the commonly chosen ones? 6th being overdrive.

cheers

also, does anyone know what the mainshaft to countershaft distance is on the seq holinger?

ie. the os88 is 88mm....

There are no set ratios, leagh at Hollinger will send you a chart to choose from, Tomei has chisen two different otions.

Imput shaft can be standard 24 spline but most people choose the chevy 26 spline unit as this was a weak point of the original nissan gearbox.

Main shaft to counter shaft distance, call Hollinger.

If you buy one be prepared to put regular gearsets in it, they do wear out and are costly.

  • 9 months later...
Beer Baron Grand Master

Beer Baron

Posted
Posted

pretty sure the GTR hollingers are an HS6 so yeah with the right bellhousing and adapter for the transfer case it should be fine. as long as what you're buying from a V8 is an HS6 too. call hollinger and I'm sure they can tell you. but by the time you buy the right hollinger/RB bellhousing, and the transfer case fitting it might not be worth it. also need to take into account the ratios it comes with might not be suitable.

Beer Baron Grand Master

Beer Baron

Posted
Posted

actually looks like they are not an HS6 after all. and apparently V8SC don't use HS6 now either. it's still possible you could buy one and then buy the bellhousing for the front and the transfer case mount/adapter for the rear but again by the time you do all that just buy the right GTR box?

have a look at the holinger site. it's been updated recently I was told. if you look at the centre of the old GTR boxes (which is the gearbox with the front being just bellhousing and the rear is transfer adapter) it does look a bit like an HS6 but better to check before doing anything.

Beer Baron Grand Master

Beer Baron

Posted
Posted

don't worry I've had that same thought before too.

"hmm, plenty of 6spd sequential hollingers getting around in varous V8SC.... hmmm now how do I put that into my GTR???" lol.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      New fix for low tyre pressure from bmw

      By Duncan · Posted

      I had never actually looked into it, but aren't onboard compressors a thing in trucks?
    • sunsetR33
      Anyone have this problem with their temperature gauge?

      By sunsetR33 · Posted

      Read the ECU for fault codes or have someone else do it. A faulty coolant temperature sender is usually listed in ECUs. If the sensor itself is not busted it can also be a bad ground connection. Or in a really unlucky case, damaged wiring.
    • sunsetR33
      Anyone know this frontpipe?

      By sunsetR33 · Posted

      Can't be a Futjitsubo as those are made with a flex piece and Reimax is smaller in pipe diameter. If anything it is closest to a Mines pipe, but evidently it is not an actual Mines pipe.   Classic word humor
    • sunsetR33
      Anyone know this frontpipe?

      By sunsetR33 · Posted

      Alright I will try to not forget.   As GTSboy replied to you already, problem is mainly the mismatch between the actual exhaust part and the denomination in the papers. That basically just looks like tampering to a cop, if they were to check your car and notice. If it had been done right they would have clarified it to be a custom pipe and just given it a certain part number that you have to engrave or weld onto the pipe. I will definitely inquire on what to do. Changing the pipe wouldn't be my favorite solution as it costs a bunch of money and the cat was fitted with the front pipe and exhaust under the car, and if the front pipe flange does not sit in the OEM location the cat will need to be refit for any other pipe to work. It also usually doesn't need a brand name or something like that, but more something like a part number. Usually for exhaust parts, on silencers and cat units specifically, there is a badge that reads the certificate number that belongs to these exhaust parts under EU regulation. You get these numbers after you put a part or group of parts through the tedious testing according to EU vehicle legislation and they pass. You can find these "part numbers" on various parts throughout a EU vehicle. On windows, headlights, engine parts, seat belts and so on. All these parts have gone through standardized testing and acquired a so called ECE or EG Certificate that makes them legal to use by themselves in all countries that adhere to these standards. You can also not alter these parts in any way, if you do they become illegal. An example for stampings on an exterior lighting part, the people who need to know can find the documentation for this unit in a database. I do not know what all the standards and so on mean.
    • Rezz
      Anyone know this frontpipe?

      By Rezz · Posted

      If that was the case I suppose you could call it "Mein's" brand....  ... I'll see myself out... 😅
×
×
  • Create New...