Jump to content
SAU Community

Recommended Posts

I have for sale a RB26DETT Forged Short Motor

Built for big boost and HP by RB specialist Stuart Jones of Cavehill Enignes

NEW

JE custom forged pistons , with contact reduction and double forced gudgeon oiling

Tomei "H" forged conrods , with upgraded ARP 2000 12 point 8740 chrome moly 220000psi bolts

Perfect Seal race set piston rings with gapless 2n/d rings

ACL Race heat treated main and big end bearings

ARP main studs , ARP headstuds

Nissan N1 oil pump

Tomei 1.5mm oil restrictor

NSK timing belt tensioner , NSK timing belt idler

KP gasket set with multi layer steel head gasket (MLS)

Block

Acid dipped , magnaflux cracktested , cylinder bores sonic test for wall thickness ( X-rayed ) ,

Bored .5mm and diamond plateau honed , Decked square to main tunnel

Crankshaft ( late 32 or 33 with long oil pump drive )

Acid dipped , electromax cracktested , measured , linished ( micro polished ) and fully balanced

Engine is assembled to short motor with sump fitted

c/w secondhand

GTR sump complete with 4.111 diff ratio

alloy engine mount brackets , p/s and a/c mounting brackets , oil filter housing , oil cooler and water pipes ,

thermostate housing , harmonic balancer

All it needs is a cylinder head , water pump and a timing belt

Price $ 8800

May trade or swap for BNR32 GTR

Can email or SMS photo's

PM , call or text

0407807195 Stu

hey mate

to get all the testing n maching done to your block

how much did it cost roughly

what are the pros of getting ur block acid dipped, magnaflux cracktested ?

Some more pic's

ARP head std kit , Adjustable cam gears

Oil filter housing , cooler assembly

Harmonic balancer , p/s bkt , a/c bkt , engine mount bkt's

Exhaust manifolds

post-37725-1282218889_thumb.jpg

post-37725-1282218900_thumb.jpg

post-37725-1282218910_thumb.jpg

post-37725-1282218920_thumb.jpg

  • 2 weeks later...

I have had a few PM's about the custom pistons

Contact Reduction Grooves: The purpose of machining these grooves is to reduce the amount of contact area

against the cylinder wall when the piston “rocks over”. Contact reduction also serves to disrupt the flame travel into

the crevice area thus helping to reduce detonation.

Double Pin Oilers: Double Pin Oilers deliver twice the amount of oil to the wrist pin as compared to the standard single pin oiler.

8800. thats abit high dont ya think

considering its a standard block with a n1 oil pump :-S

NEW

JE forged pistons , custom ordered with contact reduction grooves and double forced gudgeon oiling

Tomei "H" beam SNCM439 metal forged conrods

ARP 2000 12 point 8740 chrome moly 220000psi conrod bolts

Perfect Seal race set piston rings with gapless 2n/d rings

ACL Race heat treated main bearings

ACL Race heat treated big end bearings

ARP main studs

ARP head studs

Nissan N1 oil pump

Tomei 1.5mm oil restrictor

NSK timing belt tensioner

NSK timing belt idler

KP gasket set with multi layer steel head gasket (MLS)

Alloy adjustable cam gears

Add up all these new parts then see if $ 8800 is too high , then add machining costs

Cash talks and im open to offers

Cheers

did ur machining cost 3 grand did it

NEW

$ 3300 JE forged pistons , custom ordered with contact reduction grooves and double forced gudgeon oiling ( purchased Feb/2009 when $1 aud bought .64 cents us)

$ 1544 Tomei "H" beam SNCM439 metal forged conrods

$ 350 ARP 2000 12 point 8740 chrome moly 220000psi conrod bolts

$ 550 Perfect Seal race set piston rings with gapless 2n/d rings

$ 165 ACL Race heat treated main bearings

$ 95 ACL Race heat treated big end bearings

$ 257 ARP main studs

$ 460 ARP head studs

$ 535 Nissan N1 oil pump

$ 22 Tomei 1.5mm oil restrictor

$ 95 NSK timing belt tensioner

$ 115 NSK timing belt idler

$ 550 KP gasket set with multi layer steel head gasket (MLS)

$ 130 Alloy adjustable cam gears

USED

$ 1300 R33 , Late R32 RB26DETT sub assembly suit reco inc diff assembly ( purchased in 2008 )

Just to give you an idea on prices

Cash talks and im open to offers

Cheers

You interested or just wasting his time? :S
no hes not intrested.

His motor is worth 4 to 5 times what this guy is asking !

Thanks Guy's , for your positive inputs

Cheers STU

THE DO'S AND DONT'S OF THE SAU CLASSIFIEDS!

2. No price debates - put simply if you do not agree with the price being asked, do not comment on the thread. If you believe the seller is asking too much then either pm the thread starter or dont buy the items advertised - simple.

There is to be no "My cousin can get it for much less" or "Your asking too much" comments

did ur machining cost 3 grand did it

have u ever built an motor? i got mine back from the machine shop yesterday with a bill of near 3k just for machining/labour..

its also the time and effort to aquire the parts, big fkn headache can take months etc

Edited by Char
have u ever built an motor? i got mine back from the machine shop yesterday with a bill of near 3k just for machining/labour..

its also the time and effort to aquire the parts, big fkn headache can take months etc

too right!!!

dont even start with trying to enplane the headache!

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • First up, I wouldn't use PID straight up for boost control. There's also other control techniques that can be implemented. And as I said, and you keep missing the point. It's not the ONE thing, it's the wrapping it up together with everything else in the one system that starts to unravel the problem. It's why there are people who can work in a certain field as a generalist, IE a IT person, and then there are specialists. IE, an SQL database specialist. Sure the IT person can build and run a database, and it'll work, however theyll likely never be as good as a specialist.   So, as said, it's not as simple as you're thinking. And yes, there's a limit to the number of everything's in MCUs, and they run out far to freaking fast when you're designing a complex system, which means you have to make compromises. Add to that, you'll have a limited team working on it, so fixing / tweaking some features means some features are a higher priority than others. Add to that, someone might fix a problem around a certain unrelated feature, and that change due to other complexities in the system design, can now cause a new, unforseen bug in something else.   The whole thing is, as said, sometimes split systems can work as good, and if not better. Plus when there's no need to spend $4k on an all in one solution, to meet the needs of a $200 system, maybe don't just spout off things others have said / you've read. There's a lot of misinformation on the internet, including in translated service manuals, and data sheets. Going and doing, so that you know, is better than stating something you read. Stating something that has been read, is about as useful as an engineering graduate, as all they know is what they've read. And trust me, nearly every engineering graduate is useless in the real world. And add to that, if you don't know this stuff, and just have an opinion, maybe accept what people with experience are telling you as information, and don't keep reciting the exact same thing over and over in response.
    • How complicated is PID boost control? To me it really doesn't seem that difficult. I'm not disputing the core assertion (specialization can be better than general purpose solutions), I'm just saying we're 30+ years removed from the days when transistor budgets were in the thousands and we had to hem and haw about whether there's enough ECC DRAM or enough clock cycles or the interrupt handler can respond fast enough to handle another task. I really struggle to see how a Greddy Profec or an HKS EVC7 or whatever else is somehow a far superior solution to what you get in a Haltech Nexus/Elite ECU. I don't see OEMs spending time on dedicated boost control modules in any car I've ever touched. Is there value to separating out a motor controller or engine controller vs an infotainment module? Of course, those are two completely different tasks with highly divergent requirements. The reason why I cite data sheets, service manuals, etc is because as you have clearly suggested I don't know what I'm doing, can't learn how to do anything correctly, and have never actually done anything myself. So when I do offer advice to people I like to use sources that are not just based off of taking my word for it and can be independently verified by others so it's not just my misinterpretation of a primary source.
    • That's awesome, well done! Love all these older Datsun / Nissans so rare now
    • As I said, there's trade offs to jamming EVERYTHING in. Timing, resources etc, being the huge ones. Calling out the factory ECU has nothing to do with it, as it doesn't do any form of fancy boost control. It's all open loop boost control. You mention the Haltech Nexus, that's effectively two separate devices jammed into one box. What you quote about it, is proof for that. So now you've lost flexibility as a product too...   A product designed to do one thing really well, will always beat other products doing multiple things. Also, I wouldn't knock COTS stuff, you'd be surprised how many things are using it, that you're probably totally in love with As for the SpaceX comment that we're working directly with them, it's about the type of stuff we're doing. We're doing design work, and breaking world firsts. If you can't understand that I have real world hands on experience, including in very modern tech, and actually understand this stuff, then to avoid useless debates where you just won't accept fact and experience, from here on, it seems you'd be be happy I (and possibly anyone with knowledge really) not reply to your questions, or input, no matter how much help you could be given to help you, or let you learn. It seems you're happy reading your data sheets, factory service manuals, and only want people to reinforce your thoughts and points of view. 
    • I don't really understand because clearly it's possible. The factory ECU is running on like a 4 MHz 16-bit processor. Modern GDI ECUs have like 200 MHz superscalar cores with floating point units too. The Haltech Nexus has two 240 MHz CPU cores. The Elite 2500 is a single 80 MHz core. Surely 20x the compute means adding some PID boost control logic isn't that complicated. I'm not saying clock speed is everything, but the requirements to add boost control to a port injection 6 cylinder ECU are really not that difficult. More I/O, more interrupt handlers, more working memory, etc isn't that crazy to figure out. SpaceX if anything shows just how far you can get arguably doing things the "wrong" way, ie x86 COTS running C++ on Linux. That is about as far away from the "correct" architecture as it gets for a real time system, but it works anyways. 
×
×
  • Create New...