Jump to content
SAU Community

R32 Gtr Seats And Turbos

bent1987
 Share

Recommended Posts

bent1987 Apprentice

bent1987

Posted
  • Author
Posted

RB26 specs

JE forged pistons (im not sure how long they have been in the motor, they look fairly new and in goog condition)

Std Rods

Std Crank

N1 oil pump (Brand new only just fitted to the block)

GMP water pump (Brand new)

I would recommend that the person that buys it, replaces the rod and

main bearings for piece of mind, asking $2000 (neg) , if you have any questions send me a pm

i also have std RB26 manifolds for sale, std 32 GTR AFM's, a Dash, and all the crap under the dash, if your after something

send me a PM i might have it laying around.

roarz01 Newbie

roarz01

Posted
Posted
I have the following items that have been removed from my R32 GTR for sale:

1 x Passenger side seat and rail ($230)

1 x Drivers side seat and rail ($150 seat has a tear)

2 x Door cards (both driver and passenger sides $100 each)

1 x Roof trim (needs to be cleaned $80)

1 x Hicas pump (was working before it was removed $100)

1 x Standard fuel tank (no fuel pump $150)

1 x Walbro 255 LPH/550hp fuel pump (has only been used to prime fuel rail vehicle was never fired with this fuel pump $120)

1 x GTR wing (needs to be repainted $100)

1 x ABS unit (needs a clean was working before it was removed $250)

1 x Standard radiator (has a few bent fins $70)

6 x Standard 440cc injectors ($300)

2 x Standard R32 Turbos ($400)

1 x Front bar (slight damage, front bar mounts fine, the lip just hangs down a little in the centre, its repairable $150)

any inspection welcome, all prices negotiable, im located in Banyo, Brisbane

pm me any questions

hey mate are the injectors still for sale can i come have a look at them cant u txt me ur number to 0435713185 or pm me ur number so i can call u asap thanks

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Mitchp77
      UniClutch

      By Mitchp77 · Posted

      Hey @Butters, did you end up getting this clutch in ? I have just ordered to a uniclutch track to go in my getrag 6 speed that’s in my BNR 32     
    • Murray_Calavera
      NC MX5

      By Murray_Calavera · Posted

      I know you don't want to hear this comment, but I can't not say it.  I just can't see 200kw being worth the time and effort. Its like guys with NA cars, putting in headers/exhaust/tune for a massive 20% jump in power. Great, the slow car is still slow and you're down $10,000.  My vote is leave it NA or price in a gearbox upgrade and shoot for at least 300KW, preferably 350KW+.  Now you have a NC that will try to kill you from time to time and will be exciting to drive
    • Murray_Calavera
      How "plug and play" is the Haltech Pro for R33 GTST

      By Murray_Calavera · Posted

      Ah yep. The main message I want to pass on is, try not to get scared of ghosts when thinking about knock/knock detection.  What I mean is, healthy engines make noise. Knock is also noise. Your knock sensor and ECU combo are trying to determine bad noise from good noise based on how loud the noise is. The factory knock sensors and ECU are not good at doing this.  Modern ECU's are pretty decent at it, however I'd still say that you would want to verify that if your ECU says it's knock, that you actually listen to it and confirm that it is correct.  Are you familiar with the plex knock monitor?  https://www.plex-tuning.com/products/plex-knock-monitor-v3/ I expect you're the type of person that would be very keen to play with something like this. It is great knock detection and you can pop some headphones on and listen to what's going on.  Knock that you've deliberately induced in low load low RPM areas is not really putting anything at risk and is a great tuning/learning/verification tool.  I just thought this was worth mentioning based on the way you were talking about setting up a base map and the Haltech base map settings. There are better ways to spend your time then chasing ghosts and worrying about detonation in scenarios that it is crazy unlikely to encounter it.  I was also wondering, what ECU are you planning to get? Will it be long til you pick it up?
    • Milkmun
      NC MX5

      By Milkmun · Posted

      This came quicker than I thought. It ain't even 2025 yet.
    • Kinkstaah
      NC MX5

      By Kinkstaah · Posted

      I somehow quoted my post instead of editing it. I regret nothing.
×
×
  • Create New...