Jump to content
SAU Community

Recommended Posts

Hey guys,

Pretty sure I need new brake pads and rotors, but Im now getting a terrible grinding sound occasionally coming from the brakes when Im turning without applying any brakes..

Had a look and you can see there is definantly strange wear on the left and right sides - the rears are fine.

Im thinking a wheel bearing might be gone, but I cant physically wobble the wheels with my hands..

Any ideas?

Passenger Front.

photofr.jpg

Drivers front

photo2do.jpg

Link to comment
https://www.sau.com.au/forums/topic/333884-brakes-help-needed/
Share on other sites

oh, I fuxked up all my pads and the rear rotors today at wakefield. Anyone know what pads will be good for the track?

My V35 is an automatic without brembo. Thanks for anyhelp=)

I did just the same thing @ QR about 2 weeks ago except I managed to crack my RDA slotted discs at the front as well

Just replaced with DBA 4000 slotted up front with Ferodo DS2500 pads

Using DBA street series blank discs on the back with Hawk ceramic pads

Also did a fluid flush and replaced with Motul 600 fluid

Bring on the next wednesday arvo sprint!

I did just the same thing @ QR about 2 weeks ago except I managed to crack my RDA slotted discs at the front as well

Just replaced with DBA 4000 slotted up front with Ferodo DS2500 pads

Using DBA street series blank discs on the back with Hawk ceramic pads

Also did a fluid flush and replaced with Motul 600 fluid

Bring on the next wednesday arvo sprint!

Mind sharing where you get them and what's the price?

will those blank discs at the back works well on the track, I got the 4000 slotted on the front, they works sublime.

but those OEM back rotors are all fuxked up.

So what I am concerning is will those blank discs = oem blank discs?

and whats the price you get it?

and the DS 2500 as well?

thanks =)

I didn’t go slotted on the rear for a few reasons

1. The guy who dose my brakes wasn’t able to get any slotted discs for a week and my rears "back left in particular" were shagged due to the pads being worn out and having metal on metal run groves in the discs

2. 70% of the hard work is done by the fronts

3. Slotting doesn’t actually do that much, its more about helping gasses from the pad escape and most new pads don’t have that problem

4. A better pad will have a much more noticeable difference than a slotted/drilled disc

So with that in mind and the new rear pads being ceramic = handles heat better. I didn’t see the need for slotted on the rear

I didint shop around with the pads price, I didint have the time to and could not be funked. My brakes were only working about 30% of what they were before I went to the track and I needed to get them fixed ASAP

Anyhow I ended up paying $277 for the DS2500 pads for the front $150 for the Hawks on the rear

I have used DS2500 pads on my old 180sx in the past which had R33 4 pot calipers/discs on the front. Compared to the 1st set of pads which were probally OEM nissan ones despite the brakes being fairly large given the weight of the car. I had fade after only 2 laps, after I changed to the DS2500 I could go the whole session 6 hot laps and not have any problems.

There is a sweet spot but when it comes to pads, if you fit pads that are too heat orieanted then they dont work as well when they are cold. The DS2500 for me work fine when cold but get better when theres some heat in them

Thanks for the information=)

I didn’t go slotted on the rear for a few reasons

1. The guy who dose my brakes wasn’t able to get any slotted discs for a week and my rears "back left in particular" were shagged due to the pads being worn out and having metal on metal run groves in the discs

2. 70% of the hard work is done by the fronts

3. Slotting doesn’t actually do that much, its more about helping gasses from the pad escape and most new pads don’t have that problem

4. A better pad will have a much more noticeable difference than a slotted/drilled disc

So with that in mind and the new rear pads being ceramic = handles heat better. I didn’t see the need for slotted on the rear

I didint shop around with the pads price, I didint have the time to and could not be funked. My brakes were only working about 30% of what they were before I went to the track and I needed to get them fixed ASAP

Anyhow I ended up paying $277 for the DS2500 pads for the front $150 for the Hawks on the rear

I have used DS2500 pads on my old 180sx in the past which had R33 4 pot calipers/discs on the front. Compared to the 1st set of pads which were probally OEM nissan ones despite the brakes being fairly large given the weight of the car. I had fade after only 2 laps, after I changed to the DS2500 I could go the whole session 6 hot laps and not have any problems.

There is a sweet spot but when it comes to pads, if you fit pads that are too heat orieanted then they dont work as well when they are cold. The DS2500 for me work fine when cold but get better when theres some heat in them

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I just got to work and skimmed through 61508 and 61511. I was surprised the CSA adopted both, but neither are enforced. To recap what I read, it states that in a perfect world, they should be segregated but they acknowledge that this is not industry standard and clearly mention that they allow mixing of safety and non-safety. 61511 also mentions software segregation like AB does in their safety PLC's.   Now if only I could go back to control, let alone safety over comms. In my current line of work, we're only allowed monitoring and basic control over comms. Everything critical must still be hard wired as much as possible. 
    • I've unfortunately never been as they're on the complete other side of the continent and another country that isn't currently letting us in as easily as they use to. I even heard their stop signs over there actually say "Stop" instead of "Arret". If I decided to trek the 48h drive, I wouldn't know when or where to stop haha. Whenever I order parts from UP Garage, I order from Japan as it's cheaper. Same with GKTech... oddly enough, it's cheaper shipped from Australia then it is the US.  UP Garage Japan operates their US leg though, unlike Tomei. If Tomei JPN had the power to close down Tomei USA, I'm sure it would be done in a day. They're two completely separate entities. Tomei JPN messed up somewhere originally agreeing to its creation and got sacked big time. 
    • I asked someone about this and he told me about the Audi 1.8T engine. But I think it would be difficult to swap
    • I don't know that machine specifically, but I'd personally go for something with a little more kick than 130amp. Around up to 180 would be good. At the 6mm range, you're really pushing the machine hard and don't have a long period you can run for with out needing to give it a rest. Lots of MIG machines come with a regulator and hose. A lot will come with a starter roll of wire too, but it isn't too expensive to buy. I'd recommend NOT buying a massive roll too, as you don't want it sitting around FOREVER in the machine between uses and potentially going to shit. For thin sheet metal, get a roll of 0.6mm if you're doing over 3mm and above, switch over to 0.8mm wire. Even by 2mm you'd probably really want to switch. As for gas battle, it's all swap and go style now. You'll pay a bottle deposit, and then X amount to swap for a full one. I think it's like $200 or $300 for a D Size bottle upfront as "deposit", and like $110 to $150 per swap. My D size CO2/argon bottle lasts a fair bit of welding on the MIG. And I run an E size bottle on the TIG. For DIY MIG, stick with a D size bottle. If you really start to get into a LOT of welding and doing it really regularly, then upgrade. If you're like most DIY car guys, one D bottle will last you 2 or 3 years easily. I think I've been on my current bottle about 5 years. It is starting to get low, but I've been smashing it a lot more the last 6 months.
    • SR20s came with cars like the Bluebird and Primera, but the RB20 never came. The ones in Turkey were either brought in specially or from abroad. That's why RBs aren't as common as SRs. And if a part breaks or I need to replace it when doing maintenance, it's harder to find parts for RBs.
×
×
  • Create New...