Jump to content
SAU Community

Recommended Posts

on rb25

it's a philips head screw. bottom of the circled bit in this pic

post-20406-1142855991.jpg

it think someone lost ur flat head screw :blush: cos theyre usually flat heads :wub: i know mine is!

ps, ur throttle cable looks really tight lol, might wanna loosen it a bit if it is!

Link to comment
https://www.sau.com.au/forums/topic/333911-idle-screw/#findComment-5413602
Share on other sites

my throttle cable looks like that too.. so its in to lower revs and out to raise revs?

no not at all

loosening the throttle cable nuts will only adjust the tension on the cable, if your cable is tight then it may alter your revs when taking your foot off the pedal because the throttle plate may not close fully instantly.

its always good to have a little bit of slack in the cable

also be careful when tightening the cable nuts above the manifold, the thread is only alloy or plastic or something, so tighten the nuts up hand tight, then just turn a tiny bit extra with a spanner.

Link to comment
https://www.sau.com.au/forums/topic/333911-idle-screw/#findComment-5413723
Share on other sites

no not at all

loosening the throttle cable nuts will only adjust the tension on the cable, if your cable is tight then it may alter your revs when taking your foot off the pedal because the throttle plate may not close fully instantly.

its always good to have a little bit of slack in the cable

also be careful when tightening the cable nuts above the manifold, the thread is only alloy or plastic or something, so tighten the nuts up hand tight, then just turn a tiny bit extra with a spanner.

also I found by having a slight bit of slack in the cable my car isn't as jerky when you tap the gas the slightest bit.

Link to comment
https://www.sau.com.au/forums/topic/333911-idle-screw/#findComment-5413746
Share on other sites

it think someone lost ur flat head screw :blink: cos theyre usually flat heads :ermm: i know mine is!

ps, ur throttle cable looks really tight lol, might wanna loosen it a bit if it is!

thats not my engine bay lol.

and here's another borrowed pic. philips!!! maybe someone lost yours and replaced it with a flathead :)

post-20406-1142858982.jpg

Link to comment
https://www.sau.com.au/forums/topic/333911-idle-screw/#findComment-5415371
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yuck. But it's kinda the same principle, moving timing around to make car run bad but sound good.... I went for a more spirited tuning drive to iron out a few things. Car no longer stalls, and it loved to dip RPM low when you clutch in. After tuning this (and the 4-5 tables that HPTuners/LS1 OEM ECU wants for idle air correction) it's now behaving somewhat normal. All expected because there's a new TB, new Intake manifold and that new TB which is 102mm vs 78... has an entirely different IAC passage which is smaller because ????? Unfortunately at this point I went to make further fine tuning changes to avoid it flaring up, you know... _tuning_ the HPTuners dongle died. Well to be more accurate - The USB cable died in a fashion that anyone who has ever charged a phone will recognize. After the app demanding I resync it 50 or so times (which all 'succeeded' but all failed) the device does not want to sync and I've logged a ticket with support to see if it's fixable. US Support said it was a 'storage issue' but after removing the SD card inside it and formatting it/fixing it the issue does persist. Unfortunately usually the fix is "Turn in your old dongle and pay $700 for the upgraded one" it's cheaper because I get some free licence credits I unfortunately don't need. However I'm 10 minutes down the road from HP Tuners AUS/VCM so at least I won't need to post it, and logged a new ticket for support over here. Definitely drives different. My SOTP dyno believes it's probably making 310-320kw instead of the 280 before.  It scrambles for traction a little now whereas it previously different. It drives like a bigger cam car up top even though the cam is smaller, likely due to the cam not being advanced 6 degrees. The timing is deliberately low and the fuel is very rich so who knows if this will improve on the dyno. It may, imperceptably. Also funny is removing the pineapples definitely makes the car squat more and axle tramp less. So this behavior of having more top end, squatting more, and scrabbling for traction more makes me think = more power. But I could have just been sitting on the threshold of that kind of behavior before. Time will tell if my butt dyno is calibrated right. I need the exhaust leaks fixed before dyno tune for obvious AFR related reasons - I repositioned the pipes but I'm not confident it's fully sealed even if it is better. At least the car does drive around while I cannot tweak/tune it for now. And I have aircon again. medium success!
    • Don't use that manifold. Please don't use that manifold. Sunk cost fallacy is not worth the later pain. None of these will be relevant to the change that will come from the different turbo and manifold. As in, the effect of the exhaust will be nil, regardless of what else is changed. And all the cam and fuel system stuff is not changing either way, so has no effect. The turbo and manifold (and to a small extent the wastegate)....big change.
    • Just wanted to say thank you for your input   my man (lead mechanic by trade) and I have done a heap of work as you can imagine just to make the hot side work with the dump pipe, stupid massive intake on turbo, trying to get the waste gate on was not fun.  I’m kinda getting to the point where I don’t know if I try and make this work and not throw all this cash and time away or do I scrap the lot and start again? the Apexi I’ve got was tuned for a few slight differences:   Tomei pon cams (mine are stock neo) Turbo smart 38mm external waste gate (mines 45mm replumbed) with stainless screamer pipe  3inch turbo back exhaust with high flow cat Sard 800cc top feed injectors Sard adjustable fuel pressure reg    
    • Out here E90s are the cheapest way into a sporty-ish car because everyone knows just how expensive the repairs can get. 8-10k USD for an automatic 335i. 
×
×
  • Create New...