Jump to content
SAU Community

Fs: Plenum Spacer, Panel Filter, Pod Filter


Recommended Posts

OK guess I should try and clean out the garage, as it's starting to get hard to park the car in there...

Pure Innovations Plenum spacer - $100

This is a flat spacer (not angled) for maximum airflow but won't clear the factory strut brace without spacers. I believe I have all the spacers, will confirm tonight. Supplied with plenum gasket, but advisable to get a new one from Nissan for 100% air-tight fit. Good improvement in mid-range with this mod.

Trust Airinx-GT high flow panel filter - $50

Used for only 1 track day and a few hundred k's before boosting the car. I chose the Trust because (apparently) the filter material is the best flowing. Breathes much better than stock.

Apex'i Pod filter and heat shield - $60

If you're after a pod filter, this flows quite well and the heat-shield helps with the heak-soak.

Will post up some pics tonight or tomorrow, PM me if you're interested.

Link to comment
Share on other sites

very keen on the spacer...does it come with the spacers/washers for each bolt and extended bolts for the plenum?? If it's the complete kit and all that's required is a new gasket...then please pm me shipping cost to perth and banking details for funds xfer.

cheers

ps: can I still use the factory engine cover without fouling on the bonnet??

Link to comment
Share on other sites

What size is the plenum spacer (how thick)?

10mm thick all round.

Interested in the Pod Filter, will you ship to Perth ?

Yep shipping to Perth is all good, around $10.

ps: can I still use the factory engine cover without fouling on the bonnet??

I'm not sure about the V35/G35 but I could still use the 350Z engine cover.

Plenum Spacer and Panel Filter on hold.

Link to comment
Share on other sites

Fcruz3r; pics below...hmm I appear to be missing 3 of the small bolts when compared to the stock picture. But I've counted on my plenum and it only takes 9 bolts.

6820_TrustFilter.jpg

6819_PlenumSpacerParts.jpg

You can compare the inventory with the stock photo from Pure Innovations;

Pure_plenum_spacer.jpg

Edited by Kam-80
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • People still have Skylines? I thought they're non-existent now. 
    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
×
×
  • Create New...