Jump to content
SAU Community

"play" In The Driveline

s13-steve
 Share

Recommended Posts

Missileman Veteran

Missileman

Posted
Posted

Same problem here in an R32 GTR - clunks from the rear when driving harshly, so I put it over the pit and it has a ridiculous amount of play which we isolated to the rear diff. Next, is to remove the centre and get it rebuilt at a shop.

On that does anyone know a good place to go for a diff centre rebuild in Perth?

Do report back what they did to fix it and the cost, I have a similar issue with my R32 gtst.

Mike.

  • 2 years later...
V28VX37 Veteran

V28VX37

Posted
Posted

Resurrecting an old thread.

I'm experiencing some play in the driveline after my recent manual conversion, two different types:

  • There's a slight but noticeable 'clunk' on gear change (clutch-in). This happens most of the time but not always, and doesn't seem to be related to a specific gear or speed. This is the one I'd like to get fixed.
  • There's also slight 'slack' when changing over from accel to decel or vice versa. This feels quite similar to other manual cars I've driven but I'm not sure how 'tight' it's meant to be with an RB25DET gearbox?

I had a look under the car, I could rotate the front part of the tail shaft probably 2mm by hand, the rear part was harder to move. This is with the car in gear and handbrake on.

Which part of the driveline should I look at first?

What's the best way to check the condition of the tail shaft centre bearing?

GTSBoy Grand Master

GTSBoy

Posted
Posted

From your symptom description I would suggest the centre bearing the tailshaft would be #1 suspect.

In reality, I find that it is every single point in the driveline adding up. I have play in the tailshaft, some in the diff, some in the rear CVs and some in the rear hubs. Not enough at each point to be concerned about, but added together they create a hell of an annoying clunk in my driveline.

V28VX37 Veteran

V28VX37

Posted
Posted

Thanks GTSBoy, I'll start from there! I wouldn't be surprised either since the tailshaft is a combination of my R34 sedan rear half and an R33 coupe front half from the wreckers.

Just a couple of more observations from today:

  • There's a slight but noticeable 'clunk' on gear change (clutch-in). This happens most of the time but not always, and doesn't seem to be related to a specific gear or speed. This is the one I'd like to get fixed.

This seems to come from behind the driver i.e. centre bearing, diff, or drive shafts. Centre bearing is currently the prime suspect.


  • There's also slight 'slack' when changing over from accel to decel or vice versa. This feels quite similar to other manual cars I've driven but I'm not sure how 'tight' it's meant to be with an RB25DET gearbox?

This seems to be more in the front side so clutch or the gearbox itself. I reckon it's the latter.

I'm not too fussed about this one but the clunk on gear change is more annoying so need to get that sorted.

  • 2 weeks later...
V28VX37 Veteran

V28VX37

Posted
Posted (edited)

I just checked this again with handbrake on and gearbox in neutral. There's about 8mm of play in the diff, measured on the outer ring where the tail shaft joins the diff. Not sure if this is a little or a lot?

I also did the 'diff test' and opposite wheel rotates the same way when turning so it's definitely is viscous diff. Might be time to upgrade...

Edited by V28VX37
  • 8 years later...
elohim_imanu Contributor

elohim_imanu

Posted
Posted

Most of my play is in the half shafts. What do people do about this? OEM are pretty expensive. Like $1,600 each.

I can rotate a wheel about 15-20mm at the outside of the tyre, is this too much?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Blue/grey smoke after idle

      By sunsetR33 · Posted

      Can't you put the pistons to TDC and then do the valve seals? Or will the drop down too far to pull them back up?
    • sunsetR33
      Replacing turbo water line - any recommendations or advice?

      By sunsetR33 · Posted

      One thing I can tell you is, do it properly the first time. If you encounter unexpected problems just let the car sit for a week or two if you have to get some other parts or figure stuff out.  I'd have said go and use as many OEM parts as possible but since you want to change the turbo later on a custom kit is probably the better choice. Since I have no experience with RB25 just compare parts diagrams and images before buying a line kit and it should be easy to see if it has everything you need. Amayama has very good parts diagrams and part number lists, that is what I used a bunch to figure out what I might need. And don't forget to plan ahead and possibly renew other stuff that's easy to get to while you're in there doing the turbo lines. Happy wrenching
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4:   Hi all, good news. Engine is running and all the gaskets and seals seem to be working as intended. No leaks so far, even the JB Weld seems to hold. I flushed out the old coolant a few times and put in fresh coolant, not Nissan stuff, I decided to try the Ravenol Protect FL22, they claim it works for a wide variety of JDM cars and the opinions on it by some people were pretty good. And it has the nice poison green color! And man am I glad I bought a coolant system tester earlier this year, vacuum filling works wonders on this engine. I can definitely recommend this to anyone still doing it the old school way. All you need is compressed air supply. Will have to do a small test drive as soon as I can, I removed the gauge cluster again as the tacho needle was still bouncing around a bit but it was much better than before already.  I also found some cracks on all 4 tires inner and outer sidewalls. Apparently these tires should 't be parked on for extended periods or be kept under 0 degrees during storage, which I did not know. Clearly the previous owner didn't look into those details either, he probably bought them just cause they are cool semi-slicks. I'm just wondering how tf I am supposed to reach 30-80 degree tire temperatures on the public road consistenly, these tires were never going to work for my use case. I'll probably order Continental SportContact7 ones as these are the best allround summer tire available right now and I don't think I'll need anything crazier for now. Do let me know if you have experience with various tires and which ones you recommend.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      You have no idea how many goddamn boxes I received these past three months haha Most have been put to use by now though, luckily
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Not going to pretend I didn't do a bit of junky work this time around, but mostly due to the fact that some things I am not willing to spend days fixing right now, like wiring. I try to do most things properly the first time around.
×
×
  • Create New...