Jump to content
SAU Community

Hel Stainless Steel Braided Clutch Line Group Buy


Recommended Posts

I have no idea man. You got a link? I could never find whether it was a replacement of the whole line or just the rubber line. In theory though there is no need to replace the hard lines since they can't expand.

  • Replies 187
  • Created
  • Last Reply

Top Posters In This Topic

Too easy Ben, glad to see the QLD guys are getting them today.

Yeah I wasn't really sure on what the GTR line replaced since it was a different length than the GTST one. But I figured you GTR boys have some weird funky setup due to the AWD hence it being different :P

I think the GTST one replaces the block, but I shall soon see.

Well, I got one for my GTS-t, not the GTR..... Box is marked "suit 32 GTS-t" but I've been looking this morning and I'm mildly confused. lol

Let me know what you guys find?

Oh yeah that's right, you had a GTST kit, my bad :P

My mate has his engine out at the moment so i'll quickly dummy fit the clutch line from the master cylinder and see how it all fits.

Edited by PM-R33

So here is the clutch install on my mates GTST.

post-35676-1286708817_thumb.jpg

As you can see it replaces the entire factory setup :D

Here is the massive factory line removed.

post-35676-1286708775_thumb.jpg

For those kids keeping track of their cars diet here are the results:

Factory setup - 828g

New clutch line - 97g

Weight saving of 731g

Not bad ay :)

It's finished man, hence the pictures above of them fitted.

If I do one again i'll let you know.

Edited by PM-R33

Groovy!

My engine and box is out at the moment so I couldn't get a picture of it in my mind. That's a great weight saving! I'd spend an entire day trying to save that weight elsewhere :D

Yeah it's pretty decent. And in reality it would probably be closer to 800-900g because there would be less fluid used in the new clutch line compared to the amount that runs in the factory line :thumbsup:

Edited by PM-R33

That looks awesome getting rid of all that factory crap lol will be much neater. Will have to put mine in on the weekend. Pics help alot

Thanks again Phil :)

Thanks guys.

I'm going to look into whether HEL would do some custom made braided lines to replace the four brake lines on the firewall (for ABS models) or two brake lines on the firewall (non ABS models) that go from the master cylinder.

No real "performance" benefit but I figured for the good prices we are getting these at it would be a nice looking mod in the engine bay :) I've seen a few pictures of guys that have done it and it looks quite good.

I'll let you guys know if some of you would be interested; I know one of my mates is very keen.

Edited by PM-R33
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I replaced the whole clutch line with the chase bays braided hose, I think it removes that loop, is it the short hose that comes immediately off the slave or is there a drawing in the manual to find what you’re referring to? It was just re-bled when I upgraded to the nismo slave, old slave worked fine but I thought that might help, didn’t change a thing. It’s like the first half of the pedal is pushing air and then when it finally actuates the master the friction zone is tiny. Makes it practically impossible to launch the car
    • Yep, that was one of the things we learned fast in the past with our MX5. When you drive with the top down, you are effectively standing out in the sun, 100% of the time, and not getting in any shade (because roads aren't shaded generally!). Just like standing out in the middle of a field on a sunny 27C day is a bit of a bad plan, so is sitting in a MX5 without sun protection.
    • I also just ordered some Frankenstein bolts and side mounts to fit a hard top Just in case I do find one, basically so it doesn't need to be fixed to the car with only the front latch.......and then gaffa tape to keep it in place for the RTN journey from wherever I get it
    • If your temps are fine now, you probably won't have any issues with where your vents are as they don't look right up at the windscreens high pressure area, so any differences when giving it the beans for extended happy laps would be minimal, but, they should vent heaps when stuck in traffic  Much like how that reverse cowl on my SS let "visible" heat out when stationary, but, because it was basically at the windscreen my coolant temps on the Hwy actually raised because air was being fed into it at speed (110kph), to only come back down to around 90° when I got off the Hwy And your 100% correct about the NC currently not needing vents, but, if I was to add a turbo, and a oil cooler and intercooler in front of the condenserand radiator, and then take it to the track???? It is apparently a recommend requirement if I don't want to worry about coolant or oil temp issues, but, any of the above are possible scenarios, over time As it sits now, with the triple pass radiator and stock air conditioning system, I have absolutely no issues with either temps or air conditioning efficiency, I've been basically daily driving thie car for the last month, both on the Hwy, and peak hour, bumper to bumper traffic, but, that's pretty much expected from basically a standard engine  Talking about no issues daily driving, it was 39° the other day and I was sitting in bumper to bumper traffic on the M5 and then M7, with the top down, and with the air conditioning blowing nice cold air on my feet, balls, and face, well, there was one issue, my head and arms got pretty sun burnt Note to self: leave a hat and sunscreen in the car for such days 🤣
    • I would agree, unless you need something specific to the HV motor/battery side repaired or investigated, any mechanic will be able to perform normal services, but if you prefer, maybe look for a mechanic who regularly services/repairs Nissans, the VQ engines are pretty common in the Nissan lineup.  Sorry, I can't make any suggestions, I don't live in Vic.
×
×
  • Create New...