Jump to content
SAU Community

Recommended Posts

i guess it wasn't to long since the last post so its not too bad if I continue here

has anyone created these yet? this was the first (and only thing) I hated about the r33 bodykit.....and to me it seems most r33 owners share this feeling....so with such a large demand for this product....why the hell hasn't it been made yet??

Seriously...its 2012......far more unique parts have been made for far more unique cars, and are sold in bulk (especially on eBay) yet no one can seem to create glass fog-lights?

I will probably end up using tail light film to give it a blackish appearance...but also wanted to know if this was given up on as id prefer to do it the right way.

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

i guess it wasn't to long since the last post so its not too bad if I continue here

has anyone created these yet? this was the first (and only thing) I hated about the r33 bodykit.....and to me it seems most r33 owners share this feeling....so with such a large demand for this product....why the hell hasn't it been made yet??

Seriously...its 2012......far more unique parts have been made for far more unique cars, and are sold in bulk (especially on eBay) yet no one can seem to create glass fog-lights?

I will probably end up using tail light film to give it a blackish appearance...but also wanted to know if this was given up on as id prefer to do it the right way.

If i had a lens to make a mold , i have access now to water clear no bubbles or disortion epoxy polymer from USA it comes out perfect and UV stable , cost wise they would be around 15 bucks or less to make depending on volume

Damn, i already gave both of my spare orange lenses to psi parts to make moulds which it seems they wernt able to do, you could maybe contact them and see if they still have em, i gave them to them for free so maybe they would pass them on for this good cause...

The waterclear polymer epoxy resin is stronger then glass , I use it for carbon, kevlar parts

It isnt availble in austtalia and its not casting resin

Which turns yellow in uv or spiderwebs in Uv

you can smash this with a ball peen hammer and it wont shatter , can video to prove it !! its made by aerospace composites company

Oh and its high temp stable , into the 300c range plus

Edited by Carbon 34

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • https://www.efisolutions.com.au/coolant-temperature-sensor-bosch-180sx-s14-s15-r33?gad_source=1&gclid=CjwKCAjwzMi_BhACEiwAX4YZUHsCQhbiDT_NC3q5wD9jrzH6Dts9eGSr19NXSDw7x9WVm1sH7G3S4hoCwaUQAvD_BwE this is the one i replaced today
    • I have replaced the larger coolant temp sensor, i do see a smaller one next to it (looks to be just 1 pin) but i assume that is just for the dash? or should i replace that aswell?
    • Check coolant temp sensor ~ symptoms fit the hard hot start/cold start OK scenario --- if sensor goes open circuit, ECU thinks engine is cold and enriches mixture ....works when engine cold, but floods them with rich mixture when hot (Hyundi MAP engines are a bit infamous for this)...
    • OK, starter changed for a spare without much trouble. Neil had kindly left space to get to the top starter motor bolt from above with a long spanner which makes the whole deal much easier, and everything else was neat and easy to get at from underneath. Once the starter was changed everything was good, unplugged the CAS and turned the motor on the starter to make sure everything was free and happy. Onto properly priming the oil and first start. I'd picked up one of these oil prime kit from Boost doc a while back and this was my first time using it.  https://boostdoc.com.au/products/engine-oil-prime-kit?_pos=1&_sid=28c628a65&_ss=r While I'd organised all the fittings to hook it up to my GTR (sump plug to -6 feed and -4 T to tap it in and retain the oil pressure gauge, neither suited on this car as the oil pressure needs to T into 1/8 NPT not -4 and the Aeropro sump has some massive drainplug not that factory whatever it is. So, waiting for a couple of fittings, then I'll prime it and do first start, hopefully next weekend. Other than that going well, there is very little stopping a final alignment, tune then shakedown day
    • Also to mention, i just tested the CAS, seems to be working fine, can hear the pulses inbetween 0 and 180 degrees, another mention aswell, when i let the car sit for about a hour today, i went to start it and it almost fired on first crank, then just completely struggled. Could it possibly be blocked injectors?, maybe allowing a little bit of fuel to seep past allowing it it almost start first crank?
×
×
  • Create New...