Jump to content
SAU Community

Diff Ratios

sinister_rb_s14
 Share

Recommended Posts

20SIX Community Regular

20SIX

Posted
Posted

So my s13 has a 4:11 6x2 bolt diff in it, and has a new rear cradle in it also. ( under the assumption it's an r32 gtr diff and rear)

I've Damaged the diff or bearings, so will be removing and inspecting.

I did pick up a spare diff awhile back that have sitting there, it's also a 6x2bolt. It has stamped on it '38311' and 'A3'. Would this be the teeth count/ratio?

GTSBoy Grand Master

GTSBoy

Posted
Posted

1st thing. If by 6x2 you really mean 6 bolt flanges arranges in 3x2, then it's not GTR. GTR are evenly spaced 6 bolt. S chassis diffs and NA R chassis diffs are 3x2.

The ratio will be easily worked out by looking on the circumference of the crownwheel for the markings which will be some big number like 37 and some smaller number like 9 (for a 4.11 - other similar numbers for the other similar ratios like 4.08, 4.36, 3.89, etc). Inside the diff. Not on the housing. Anything on the housing can mean nothing about the internals.

  • 4 weeks later...
20SIX Community Regular

20SIX

Posted
Posted (edited)

Ahhh okay. Yeah I pulled my diff out and had a look it's a 4:11 (4:08) also has vicious lsd stickers on it

And it would be out of an abs model as it has the hole for the sensor at the front of it where tails shaft goes in.

I've smashed a tooth off the pinion..

So looking to source a replacement now.

I have another diff but it's non abs 3.91 and sounds abit worn, doesn't look like would fit anyway.

Any idea what my diff would be out of? Stagea only possibility? ( some stage before I bought mine someone has replaced the rear cradle with brand new genuine Nissan)

Also for a gtr diff, would I need to fit whole cradle, and what about hubs for the shafts?

Edited by 20SIX
  • 3 weeks later...
20SIX Community Regular

20SIX

Posted
Posted

Hey mate, got it sorted.

Turns out I had the silvia diff r200 4:08's abs model. (3x2 6 bolt shafts)

Bought an r200 out of r33 4:11 abs 5 bolt shafts.

I changed the rear hat over from the silvia diff to the 33 diff (silvia one being 4 bolt rear and 33 2 bolt)

Then the 33 diff front mounts run bushes and longer bolts instead of being solid mounted like s13. So ended up buying some cnc machined solid bushes and aquiring the longer bolts to suit..

The 6 bolt Silvia shafts fit straight into the 33 diff and all is good.

20SIX Community Regular

20SIX

Posted
Posted

Also had the 33 diff pulled down, new bearings and shimmed and backlash set etc.

now I just need to save my money to do the one piece tailshaft ( my 2 piece is just about stuffed) and remove and rebuild the rb25 gearbox as syncros aren't happy in higher rpm. ( only on 13 psi also)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Sean'O
      3D printing fun

      By Sean'O · Posted

      No worries at all 🫡 I think the most satisfying things to make are the little bits that are just impossible to find or they're no longer manufactured. Generally I always try to replace parts with OEM wherever possible. This little project is also great because it'll never see the light of day, but strengthen these brackets so it's not just relying on the little standard screws in the headlight plastic. As soon as I saw the standard brackets and screws I thought, "well I'm not going to install with just the screws, the plastic tabs will just snap off". It's crazy how expensive everything has become yeah. But I suppose that's supply and demand; granted it's a lot easier to get brand new genuine parts these days which is fantastic 😊, I don't have to get totally reamed at the local Nissan dealer ha ha We sure are lucky we have all these manufacturers making parts these days, a few really great Australian companies too like Platinum Racing Products and Fit Mint Automotive, what a time to be alive ❤️ . I've got my eye on the RB26 head by PRP as mine has a very fine hairline crack, so that'll need to be addressed some time in the future. If you have any requests or odd things to make feel free to let me know and I can have a crack at making replacement parts ✌️
    • Duncan
      3D printing fun

      By Duncan · Posted

      Thanks for sharing this, and BTW if your headlights are in good condition they are worth thousands....you might want to consider replacing them with brand new LED ones like this (https://www.nengun.com/78works/full-led-headlights-r32-skyline) and making enough profit to buy a house in Sydney
    • Duncan
      R32 GTS (RB20DE) clogged cat

      By Duncan · Posted

      I'm not sure what sort of shops are nearby, but I'd expect any reasonable exhaust shop could put a cat in it that will not restrict the power that engine makes. Otherwise, if you want to remove it, short lengths that replace the cat are readily available online, search for "de-cat pipes" or "test pipes"  
    • Sean'O
      3D printing fun

      By Sean'O · Posted

      Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 😑. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
    • GabsReDeal
      R32 GTS (RB20DE) clogged cat

      By GabsReDeal · Posted

      Hey everyone, This is my first post apart of the introduction. I tried searching a bit on the forum but couldn't really get a straight answer. I got the car to my mechanic as I felt it being weak. It seems that it was missing on two cylinders due to the injectors. I had all my injectors clean and the car runs much better. The mechanic also confirmed my suspicions that the cat is clogged and needs to be tackled asap. The cat rattles a bit and the hot exhaust warning frequently lights up when driving after getting the injectors clean. In my introduction I was asked about what modification I might be interested in and mentioned a cat delete. From what I was told, this is not really beneficial on the RB20DE and there are more cons than pros.  Could perhaps anyone give some suggestions on what the best course of action would be since the current cat is toast and needs to be removed/replaced anyway? I can also sometimes smell a strong smell of fuel, but I'm not sure if this is related.
×
×
  • Create New...