Jump to content
SAU Community

Recommended Posts

  • Replies 107
  • Created
  • Last Reply

Top Posters In This Topic

ahaha nice thread david... bringing all the tree huggers n murders together... since we're all here now lets organise a picnic ill light the bbq with my fast and furious flames coming form my decat... n the that poxy tree hugger nic a31 can do the dishes.... let me know date and place????? who's in??? ooo wait my cars impounded n im goin court soon.. soo im gona need a lift? :/

post-76568-1285597799_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/335959-decat/page/6/#findComment-5468760
Share on other sites

Since I couldn't find it, I emailed EPA a while ago and finally got a reply.

Dear Nic:Your email was forwarded to an Officer in the Environmental Enforcement Unit of the Department, who has responded below; I trust this helps with your query:

The Commonwealth Motor Vehicle Standards Act 1989 allows for the Minister to determine national vehicle standards. Information about the Australian Design Rules and emission requirements may be found here and here.

In regards to offenses for removing a catalytic converter, Section 13A of the Motor Vehicle Standards Act 1989 provides offenses for the modification of a standard vehicle and making it non-standard, and applies a penalty of 120 penalty units.

The Commonwealth Crimes Act 1914 (Section 4AA) specifies a penalty unit to be $110, and thus the removal of a catalytic converter would carry a maximum penalty for an individual of $13,200. In relation to an offence by a body corporate, Section 4B allows for a court to issue a penalty of 5 times the amount of the maximum pecuniary penalty that could be imposed by the court on a natural person, being $66,000.

Settled.

Edited by Nic_A31
Link to comment
https://www.sau.com.au/forums/topic/335959-decat/page/6/#findComment-5471383
Share on other sites

I would like to see the figures for anyone who has actually received this fine in Perth, i recall this discussion on another forum a while ago.. i'd put my money on 0.

...even the inspectors @ pits will tell you to install a cat and come back again. Good scare tactic though!

Edited by endless
Link to comment
https://www.sau.com.au/forums/topic/335959-decat/page/6/#findComment-5471586
Share on other sites

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
×
×
  • Create New...