Jump to content
SAU Community

18 Inch 4 Stud Chrome Wheels Suit Na Skyline

Victory
 Share

Recommended Posts

Victory Mentor

Victory

Posted
Posted

I have a set of four 18 inch chrome wheels for sale.

They are 18 x 7.5 inch wheels, with a +40 offset and a 4x114.3 pcd.

They would fit a non turbo R33 Skyline, non turbo R32 Skyline, S13 Silvia / 180SX, and A31 Cefiro.

The front tyres are 225/40 zr18 Achillies ATR Sport with an average of 5.5mm tread (75%).

The rear tyres are 235/40 r18 Hankook Ventus HR2 with an average of 3.5mm tread (40%).

These were on a R32 non turbo Skyline, I've done a 5 stud conversion so I can't use them anymore.

They also include 3 centre caps.

I'm asking $450 for them ono.

I'm located in Wollongong NSW, for Sydney buyers I can meet you at Heathcoate McDonands to save you a trip to Wollongong or I would be able to post them at the buyers expense.

If you are interested, send me a pm.

Clinton.

post-24210-1284103436_thumb.jpg

post-24210-1284103481_thumb.jpg

post-24210-1284103511_thumb.jpg

post-24210-1284103541_thumb.jpg

post-24210-1284103574_thumb.jpg

post-24210-1284103724_thumb.jpg

kjb_r33 Experienced

kjb_r33

Posted
Posted
where were these rims purchased ? what brand are they?

A friend of mine is interested in these for his libero, can you send PM me your phone number so i can pass it on.

Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • silviaz
      Fourth gear grind

      By silviaz · Posted

      Does your rb gearbox have the common input shaft bearing sound? (One one where it goes away when u push the clutch in or get to higher revs) I heard if you put the wrong oil it can get this sound.
    • GTSBoy
      ugently need expert / experienced opinion

      By GTSBoy · Posted

      There's more than one way to skin that cat, and most of the sump Maatouks have done will be GTR sumps. They are HUGE in GTR drag racing here.
    • dbm7
      Shifting questions

      By dbm7 · Posted

      Yeah...I always start at the shift solenoids, because there's only a few reasons these will spook into limp mode, and bad shift solenoids is one ~ the other can be the shift control module (if you have steering wheel shift buttons)...it's easier to eliminate the solenoids first.
    • cabramatta
      Never ending fuel pump drama

      By cabramatta · Posted

      Might piggy back off this thread since there's been a good discussion about PWM.   I purchased a Walbro 460 F90000267 and have been looking into PWM to understand it. It was purchased more of a future proof as my original OEM fuel pump died (r33 below 200kw) and figured I'd just upgrade it to this. That's when it hit me that a pump this big can cause more dramas with such high amperage draw and heating of the fuel pump being on 100% all the time in such a mild setup.   I have a Nexus R3 and slowly collecting power mods but I was looking into the PWM feature on the NSP software:   Then looking at the graph from the fuel pump:     Am I safe to assume reducing duty cycle to 50% for example would make the pump run like a 230/lph ? Where does the PWM come in all of this ?   I've gone down the rabbit hole of PWM fuel pumps and it seems there are many differing opinions on how to go about it 😅  
    • DRoc81
      Shifting questions

      By DRoc81 · Posted

      Thank you, this will keep me busy for a bit.  I will update progression.
×
×
  • Create New...