Jump to content
SAU Community

Recommended Posts

Hi have a few things laying around, need to get rid of these to fund new engine.

1. R32 Rear wing in metallic black Fits R32 ONLY....too wide for 33 - $200

2. R32 3.5inch Stainless Lobster Welded Exhaust, has 3 inch mild steel inlet then goes 3.5 all the way through with single XForce Cannon, excellent condition. $300

Located North Coast NSW

All Offers Considered, Cheers

Pics,

34337_403998070987_602510987_4884903_2238015_n.jpg

37376_403998145987_602510987_4884909_6370999_n.jpg

11442_169839230987_602510987_3319651_688881_n.jpg

11442_169839260987_602510987_3319655_4549790_n.jpg

I have absolutely no idea what type it is, fits r32 boot perfectly, looks like 33 gtr wing but its too wide for a 33 boot.

its not on my car atm i just sat it on the boot to see what it would look like.

need this stuff gone $120 wing

$250 exhaust

ono

Edited by DuFFR32

Any chance you can take a pic from the side but further out? so can see what the wing looks like in proportion with the rest of the car

Thanks for the message

I'm about 1 hr north, going away for a week will contact you when I get home and drive down and look.

Cheers Chris

I apologize for my absence on here, went to aus post to see if I can post exhaust but they wont take it cause the front pipe it too long. :P need to find courier any ideas?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...