Jump to content
SAU Community

Recommended Posts

first a quick run down of whats going on any help would be great as we have exhasted all options.

its on the dyno getting a tune the A/F perfect 12.0 threw the rev range but just excess fuel black smoke coming out of the exhaust.

now we have changed O2 sensors on the dyno A/F reader also borrowed another one from another tuning shop down the road, both read fine and identical when charts compaired. pulled my car off and put a differnt car on the double check and the sensor is reading perfect.

now there is no power loss and response is great but just excessive black smoke and fumes/fuel you can smell it.

put a brand new O2 sensor in can come out black as f*** also changed plugs after and where realy carboned up.

run down on engine

fully forged

head work

cams tomie b

-5 turbos

pfc pro

z32 afm's

full race twin kotomoto exhaust

dumps

hard piping kit intake and cooler

blitz bovs

hks twin power cdi

yellow jakets coils

800cc sard

tomie reg

044 surge tank

hks cam gears

any ideas would be great cheers

Link to comment
https://www.sau.com.au/forums/topic/337935-400kw-gtr-fueltune-issue/
Share on other sites

its twin seperated from the turos right back,

sensor was put in both tail pipes both read identical so this ruled out the first 3 and last 3 cylin runnin differnt

also the exhaust has 02 ports just after dumps, put in both sides up front and same thing reads perfect A/F ratios

its twin seperated from the turos right back,

sensor was put in both tail pipes both read identical so this ruled out the first 3 and last 3 cylin runnin differnt

also the exhaust has 02 ports just after dumps, put in both sides up front and same thing reads perfect A/F ratios

Sounds like super polished combustion chamber - did you specify a combustion chamber suface finish? However if the pulgs are black then I would be looking at the tune. Any chance its really rich on cruise and idle?

only when it get into load the dyno room starts filling up with smoke and fumes

on idle and cruze its fine.

the reason for the retune in the first place is i had some crap go threw my turbos, had the turbo wheels replaced and fitted them backup.

changed the catch can setup from intake sucktion to just atmo filter. also put the blitz bovs on and hks twin power.

when its a full noise and bellowing out black smoke the afr are reading a perfect 12.0 that why its got us stumped. we even wiped the tune and started again but same thing.

super polished combustion chamber why would this cause bellows of black smoke? the head was ported and polished and also the combustion chambers where polished but cant see that being the reson for the smoke.

and i dont mean a little puff of black smoke, it filles the whole dyno room in a power run its that bad. but power is there 375awkw on pump fuel straight up

only when it get into load the dyno room starts filling up with smoke and fumes

on idle and cruze its fine.

the reason for the retune in the first place is i had some crap go threw my turbos, had the turbo wheels replaced and fitted them backup.

changed the catch can setup from intake sucktion to just atmo filter. also put the blitz bovs on and hks twin power.

when its a full noise and bellowing out black smoke the afr are reading a perfect 12.0 that why its got us stumped. we even wiped the tune and started again but same thing.

super polished combustion chamber why would this cause bellows of black smoke? the head was ported and polished and also the combustion chambers where polished but cant see that being the reson for the smoke.

and i dont mean a little puff of black smoke, it filles the whole dyno room in a power run its that bad. but power is there 375awkw on pump fuel straight up

Polished combustion chambers cause less atomisation hence the 12:1 AFR and exess soot. Seen it on many cars with polished combustion chambers. The sards wont give you great atomisation either.

only when it get into load the dyno room starts filling up with smoke and fumes

on idle and cruze its fine.

the reason for the retune in the first place is i had some crap go threw my turbos, had the turbo wheels replaced and fitted them backup.

changed the catch can setup from intake sucktion to just atmo filter. also put the blitz bovs on and hks twin power.

when its a full noise and bellowing out black smoke the afr are reading a perfect 12.0 that why its got us stumped. we even wiped the tune and started again but same thing.

super polished combustion chamber why would this cause bellows of black smoke? the head was ported and polished and also the combustion chambers where polished but cant see that being the reson for the smoke.

and i dont mean a little puff of black smoke, it filles the whole dyno room in a power run its that bad. but power is there 375awkw on pump fuel straight up

12.0 isnt perfect. different for every car. under full load 13 idle 14.7 is a good start.

What else causes black smoke? Everyone tells me my Stagea blows black smoke, but I've had it dyno tuned so it goes ramps up to 11.4:1 up in the revs. Would that be too rich? I have a 100cfm 5" cat, would that have anything to do with it? Sorry for hijacking.

when your turbo's crapped themselves did oil go through ur intercooler? you may have residue oil in there that get pushed up under boost... another thing to check is decel fueling coz if its real rich it takes some time to burn all the excess away. What ECU are you using?

when your turbo's crapped themselves did oil go through ur intercooler? you may have residue oil in there that get pushed up under boost... another thing to check is decel fueling coz if its real rich it takes some time to burn all the excess away. What ECU are you using?

Turbos didnt fully crap themselfs, i was doing some maintance checks and fould my comp wheels abit chewed up, so just had new front wheel put on.

if it was burning oil it wouldnt be black smoke would be blue. also you can smell that it def fuel.

its running a pfc pro

reguards to plugs running .7 gap and not sure what heat range, same as what we have always run tuner has them in bulk lol

What else causes black smoke? Everyone tells me my Stagea blows black smoke, but I've had it dyno tuned so it goes ramps up to 11.4:1 up in the revs. Would that be too rich? I have a 100cfm 5" cat, would that have anything to do with it? Sorry for hijacking.

when you baby it around then only give it stick now and again it blows out all the deposits (condensation and carbon type build up).

when you baby it around then only give it stick now and again it blows out all the deposits (condensation and carbon type build up).

Hmmm that could be it. Gets babied most the time and give it the stick every now then..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bump on this to not make another post, had a ‘head drain’ leak on me and have the engine out as we speak. Planning on just putting a new freeze plug back in , plug the tapped holes and just be done with that headache.    Now I still want to relieve pressure to allow oil to pass down the blocks returns easier. I’ve seen catch cans with multiple vents help folks with this issue on this forum.  I’m wanting to make my own. I have some pictures here of my setup if anyone can help how I should plumb and design the catch can I would deeply appreciate it !   rb25 Oil upgrades: 1.0mm restrictor n1 pump/billet gears extended crank collar  extended sump with trap doors/w welded fitting    
    • The Frenchy's kit is the way to go forward. A modern compressor that weighs about 1/2 as much, is at least twice as efficient, and will do a good job on R134a. And of course the kit has everything else you need to connect it up and have it work properly.
    • Hey all , I am in the process of having the AC system in my r32 GTST converted from r12 to r134a and I’m being told my compressor has gone bad and I will need a new one. I was wondering if anybody has any suggestions for what is the best route to go aside from dropping $1500 on a new oem one? I did see that Frenchy’s performance garage offers a kit to mount a Toyota compressor, has anybody actually used this kit on their car? Or is there anywhere I could purchase just a clutch? Any help is appreciated.
    • Well, your RB20 ECU loom won't have wires for the boost solenoid, that boost sensor, and possibly one or two other things. There could be differences in seemingly random things like the charcoal canister purge solenoid, because the 25DET has to handle boost in the vacuum system and the 20DE does not. I don't know - I haven't looked. It is very likely that all the most important things are same-same, being the main sensors like AFM, CAS, etc, and the injectors and ignition. Not that you'll need the AFM for the Haltech anyway. I would suggest that you would seriously want to sit down with the pinouts for both ECUs and just go through them and highlight green what is the same, orange what is different/missing, and make a plan from there. It's not going to be difficult. It will either be the same or need to be fixed.
    • yeaaa that's why I haven't done any wiring to the stock ecu harness because I have the haltech, but then that leads me to the other question of "is the pnp harness really plug and play?" or would I have to still switch some pins/wires over because the pnp is for the rb25det neo harness, and not for the rb20de neo harness. was really hoping to find something to spoon feed me since so many people have done rb20neo + t conversions, but man this is rough.
×
×
  • Create New...