Jump to content
SAU Community

Hellaflush Fitment , Police Question

littletimmy

By littletimmy,
in Victoria

 Share

Recommended Posts

Panko Collaborator

Panko

Posted
Posted
Pretty sure that was just BS, I got pulled over by him after all those rumors. As far as Knox still being bad you better believe it! I only drive past knox if I have to.

I think you were the one that I saw got pulled over by a popo on Stud Rd just before the shopping centre when you were still driving NA R33??? That was a while ago as well. I get nervous when I drive around there as well.

UNR33L Grand Master

UNR33L

Posted
Posted
I think you were the one that I saw got pulled over by a popo on Stud Rd just before the shopping centre when you were still driving NA R33??? That was a while ago as well. I get nervous when I drive around there as well.

Yeh that was me in my old car while I was on P's, but also after that got pulled over again (also in the NA 33)

Now with the GTR and no P plates, I have cops up my ass that check things out and then bugger off else where - the only time I've been pulled over in the GTR was by Graeme from SAU lol :down:

joeyjoejoejuniorshabadoo Grand Master

joeyjoejoejuniorshabadoo

Posted
Posted
i've been defected 3 times in 12 months because of my fitment in my s14.

i always got the story that, if i hit some kid my evil wheels would suck the kid under the car LOL

helenlovejoy_t6301.jpg

SABBAi Grand Master

SABBAi

Posted
Posted

Just thought I'd add this.

hellaflushsig.jpg

I'm rolling flush on 9.5 +22 on the Stagea, not silly low though. Doesn't pull to much attention anywhere, probably cause it looks like a herse...

P5261336-1.jpg

Excuse front fitment... now fixed with 9.5 +22's.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • DRoc81
      Shifting questions

      By DRoc81 · Posted

      This was a huge help.  We followed the steps,  although shifting into 2nd was actually into 3rd for us,  and 1st was into 2nd ( steps 9 and 11) .  The long flash was the 4th flash.  So shift solenoid A is possibly the culprit.  Is this inside the transmission itself? Or is it accessible by just front the pan? Or is it bolted to the outside of the transmission?  Thanos for your help everyone
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 · Posted

      Can you enlighten me on your best practice regarding these hoses? I don't wanna make the same mistake if you already got a better solution.
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 · Posted

      I have some silicon hoses already, for example engine to watercooler. But yeah, I get the sentiment. The lower intercooler silicon hose is drippy too, despite not being very old. Does anyone except Nismo make these same lines out of rubber? Long term I think they'd be the better replacement, especially since the car won't live as hard a life anymore as in the past nor be driven as often.
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 · Posted

      I know most issues are just age related. But for example the turbo oil drains, there is dash adapters for these and you can just make a braided teflon line for them and (probably) never have them leak again. Also not terribly expensive. Can you even get the factory hardlines from new? Or are they repairable if they break?
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 · Posted

      I know it'd be much much easier with the tool. I hope I can find one that won't take 3 weeks to get to me an isn't a "Asian models kit" that has tons of (to me) useless adapters for a load of cash.   It's a summer project/fun car. I do wanna enjoy it, without endless downtime over and over. So yeah I would even go and buy an engine crane + stand to save myself the trouble of hard to reach or unreachable places going bad later on. Would also be a good opportunity to put on a Fluidamper, renew the mains seals and stuff like that. I have some money on the side that I can use for that, what I wouldn't want to or be able to do is let everything be done by a shop or have my engine completely rebuild right now. I intend to do most of the "doable" jobs myself. Pulling an engine can't be that hard, can it?
×
×
  • Create New...