Jump to content
SAU Community

Recommended Posts

Series 2 Neo spark plugs?

Its about time to replace my plugs, the mechanic put platinum plugs in last time it was serviced and they havent lasted very long at all. Its starting to miss on idle like it did last time the plugs were on there way out. They are NGK R PFR6G-11.

I dont want to put them back in cause they cost like $25 each and they have only lasted me around 10-15,000km

What do u suggest?

Link to comment
https://www.sau.com.au/forums/topic/339011-neo-s2-spark-plugs/
Share on other sites

im using NGK iridium ix, but if you want to go for the best of the best, do what i have done to my cars in the past, go for this:

http://www.pulstar.com/

only reason i dont have them in my car is because i didnt have 130 bucks for all 6 when i needed them. :huh:

but next month, out go the iridium and in go the pulse's.

++++copper

They work just as well and they are cheaper: NGK BCPR6ES and gap them at 0.8mm if you think your coils are struggling. Also look for tracking marks where the coils might be shorting and consider insulating them with tape or a spray (search for examples).

  • 3 weeks later...
  KiwiRS4T said:
++++copper

They work just as well and they are cheaper: NGK BCPR6ES and gap them at 0.8mm if you think your coils are struggling. Also look for tracking marks where the coils might be shorting and consider insulating them with tape or a spray (search for examples).

Will the NGK BCPR6ES go in my series 2. Do they come pre gapped to 0.8mm? if not how do u do it safely?

hello

+ 1 for NGK BPR6ES I can not believe the difference they made, mind you my plugs where pretty bad!! when you go to buy them dont tell them what they are for

because they will try and sell you something else, in there book the neo engine is supposed to have 1.1 gap.

I am still trying to get more info on that space saver, I have found that the new falcons do have a space saver and the rim size is 17inch but not sure on rolling diameter.

  Big Jim said:
I brought NGK iridium tip plugs off ebay for about $14 each

stupid me didnt put them at 0.8mm gap and left them at 1.1mm

they are good but i do need to set them to 0.8mm due to a slight miss mid range

If your coil packs are in good condition then 1.1mm should be fine. Unless you are running big power/boost it should be fine and more to the point desirable to run the larger gap to provide the best combustion.

The stagea was running a 1.1mm gap with splitfires and 18psi with the GT-RS and no misfires. With the 2835ProS it is only running 16psi but making a bit more power still with no issues.

NGK BCPR6ES coppers have worked awesome since i put them in :) running mine with splitfire coilpacks :) (came w/ from JP)

i can't remember what was in there originally, but they weren't the right ones and it idled quite high!!

  wolverine said:
If your coil packs are in good condition then 1.1mm should be fine. Unless you are running big power/boost it should be fine and more to the point desirable to run the larger gap to provide the best combustion.

The stagea was running a 1.1mm gap with splitfires and 18psi with the GT-RS and no misfires. With the 2835ProS it is only running 16psi but making a bit more power still with no issues.

i do have a set of those yellow jacket coils fitted to the car but at about 5000rpm it has a bit of hesitation for about 500rpm then pulls really hard to the redline

very odd i think

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I thought it could be an issue because the standard plate was flexing when stressed. Maybe the original gear set will hold a bit better without flex? Last time on the dyno it made around 670nm at the hubs. Now it have bigger turbo and better intake but have not been on a dyno yet. The car is being used from family trips to drag race events. So the shifts can be a little violent. It is grinding if I shift to fast so was thinking I should overhaul it soon.
    • From the factory on RB26s there's a fitting on the intake manifold collector/"plenum" that provides pre-throttle boost signal. That's how they did it back in the day, I figure it's fine to replicate it.
    • I would be surprised if that wasn't the issue. It's probably telling you, that even if you remove the plastic liner, you may have some other clearance issues that may occur too in some scenarios. IE, tyre to guard. It looks like someone has already rolled the lip, but you may still have issues in the future IE, turning and hitting a bump etc. The fact it changes how bad it makes the noise when you are going backward vs forward is highly indicative that it's the tyre rubbing. They do make a terrible sound, even if you're only pushing a project car that has a liner hanging down on a tyre!   Has the car been lowered? If it has been, what is the measurement from the centre of the wheel hub to the lip of the guard straight up?
    • Summernats cruiser?
    • Mark's a bit smarter than people give him credit... He'd convince the person that is to become dead, to drive him to the forest first. That way his car has no evidence in it, and he's free to dispose of their vehicle permanently how he sees fit too...
×
×
  • Create New...