Garage Defend Front Canrds, 34 Gtr

[FineLine]

Bought these off a forum member but they will not adapt to what i had in mind for them

http://www.nengun.com/garage-defend/stingray

they are in good condition and designed to fit standard front bumper

450 dollars plus postage

ph. 0413 863207

[depalma-bcnr33]

Are they for standard bumper or nismo bumper? Thanks

[FineLine]

Are they for standard bumper or nismo bumper? Thanks

Standard bumper.

[FineLine]

bump for some canards

[FineLine]

bumpin.

[X-Modcarz]

Load the pics so the condition of the actual item can be seen please.

[shanef]

[FineLine]

Still got these puppys. where are all the hardcore 34 owners?

[GUN_METAL_GTR32]

hay buddy

where r u located?

if ur in melbourne ill come check them out to see if they will line up with my bar if thats sweet bro.

[FineLine]

Its a long way from melbourne to qld Julz. If you're keen however i could send one down for you to try.

[GUN_METAL_GTR32]

hay buddy

what ill do is when i get home (and it stops fkn raining) ill measure the gap where they would sit in the opening of the front bar. if u could please measure the gap from the front section of the canard top to bottom i could better guage the physical size of the thing.

ill also speak to my mate shane from psi parts and see if we could modify them and remake them again in carbon

thanks dude

[FineLine]

Not sure I know where you mean but the front section that wraps around is what i measured.

The outside measurement is 21 centimetres and the inside is 17 centimetres.

[FineLine]

canard bump

[FineLine]

Bumpin for the 34's

[drego]

are they universal?will this fit to any r33,33,34 and silvia bumpers? cheers

Bought these off a forum member but they will not adapt to what i had in mind for them

http://www.nengun.co...defend/stingray

they are in good condition and designed to fit standard front bumper

450 dollars plus postage

ph. 0413 863207

[FineLine]

are they universal?will this fit to any r33,33,34 and silvia bumpers? cheers

They are 34 gtr specific.

[FineLine]

Still here peeps.

[RBEE]

hay buddy

what ill do is when i get home (and it stops fkn raining) ill measure the gap where they would sit in the opening of the front bar. if u could please measure the gap from the front section of the canard top to bottom i could better guage the physical size of the thing.

ill also speak to my mate shane from psi parts and see if we could modify them and remake them again in carbon

thanks dude

Reproducing these in wet carbon fibre would not be hard at all. The trickest part would be making up the molds -

1) waxing component to be copied with several layers of special wax

2) coating with tooling gelcoat

3) applying poly resin and reinforce with fibreglass mash

4) repeat step 3 until a thick enough layer is built up

5) wait until cured and 'pop' it out

Once the mold is made, you can make copies of the part by using carbon fibre fabric, you could even use carbon-kevlar or even kevlar on its own depending on the look youre after.

The trick is not to stirr up the resin too much when mixing in the hardener (Methyl ethyl ketone peroxide - MEKP) - this creates bubbles and you dont want bubbles appearing all over the top of the layer of carbon fibre.

I've made up many carbon parts by using this technique.

Anyways, hope that helps.

[FineLine]

still here peeps. sexy canards for your gtr.

[Alfred Y]

will this fit on the ER34 if yes I will take it!!