Jump to content
SAU Community

Recommended Posts

HEY ALL

TRYING TO DECIDE IF I WANT TO SELL MY CAR AS A WHOLE OR PULL HER DOWN AND SELL HER IN PEICES? ONLY SELLING DUE TO OTHER COMMITMENTS.

JUST WANT TO GET A FEEL FOR WHAT PEOPLE WANT AND IF I GET ENOUGH INTEREST IN PULLING HER APART THEN I WILL. IF NOT THEN ILL SELL HER COMPLETE.

OH AND SORRY FOR THE CAPS , FOR SOME REASON IT WONT ALLOW ME TO WRITE IN ANYTHING OTHER THEN CAP LETTERS? ( GOTTA LOVE TECHNOLOGY )

ITEM : TURBO KIT

GENUINE HKS 25/30 ( LESS THEN 3000KM ON TURBO, NO PLAY AT ALL )

GENUINE HKS SERIES 2 DUMP ( LARGER WASTEGATE PIPE )

GENUINE HKS ACCUATOR

XSPEED JAPAN STAINLESS LOW MOUNT EXHAUST MANIFOLD

ALL FITTINGS AND LINES

THIS KIT MADE 270RWKW AND 840NM OF TORQUE ON MY BUILT RB24

AWESOME SETUP , INSTANT RESPONSE

PRICE - $2500.00

ITEM : BUILT RB24

ENGINE HAS JUST BEEN RUN IN WITH THE ABOVE TURBO KIT AND IS A ANIMAL!!

BOTTOM END IS BRAND NEW

SPEEDLAB CUSTOM RB24 ( CUSTOM MACHINED R34 GTR CRANK )

GRUB SCREWED CRANK

LINISHED CRANK

EAGLE RODS

TOMEI PISTONS

ARP RACE SERIES STUDS

TOMEI RINGS

PISTONS HAVE BEEN TEFLON COATED

FRESH LINE BORE AND HONE

ACL RACE SERIES MAIN AND ROD BEARINGS

CUSTOM SUMP BAFFLES WITH TRAP DOORS

CUSTOM 9L SUMP

N1 OIL PUMP

N1 WATER PUMP

CUSTOM HKS 1.2MM HEAD GASKET

THIS BOTTOM END HAS BEEN MADE TO STAND BIG HP AND BIG RPM. ONLY TOP QUALITY PARTS FROM JAPAN, USED AND THE BEST MACHINING HAS BEEN DONE.

THIS BOTTOM END HAS COST ME BIG $$$

ENGINE ( HEAD )

FULL RACE PORTING

JUN 272 – 10.8mm LIFT ( BIG ) INLET AND EXHAUST CAMS

JJR ADJUSTABLE CAM GEARS

TOMEI SPRINGS

TOMEI BUCKETS

GREDDY TIMING BELT

CUSTOM OIL DRAIN MACHINED FROM THE BACK OF THE HEAD TO SUMP.

CUSTOM PAINTED ENGINE COVERS

THIS HEAD HAS HAD OVER $7K SPENT ON IT IN MACHINING AND PARTS FROM JAPAN.

THIS WOULD MAKE A GREAT STREET ENGINE OR TRACK ENGINE.

$7800.00

ITEM : FUEL SYSTEM

ALL THE BELOW ARE NEAR BRAND NEW, SHOULD SEE MID 300KW WITH THIS SETUP

SIEMENS 587cc INJECTORS TO SUIT GTR

HKS FUEL RAIL

TOP SECRET SARD FUEL REG

BOSCH 044

CUSTOM 6L SWIRL POT

$1200.00

ITEM : FRONT MOUNT

HUGE!

CUSTOM SPEED LAB FRONT MOUNT 600X320X130

CUSTOM ALLOY PIPING ( PIPING TO SUIT GTR PLENUM )

$1000,00

ITEM : CUSTOM GTR PLENUM FOR RB20

MUST HAVE FOR ANY ONE WITH A RB20!! ALOT OF HARD WORK WENT INTO THE MAKING OF THIS. SOUNDS AWESOME.

R33 GTR PLENUM

CUSTOM R33 GTR THROTTLE BODIES TO SUIT RB20

$1500.00

ITEM : ECU-COMPUTER

AUTRONIC SM4

CUSTOM RB LOOM

COMES WITH VDO SENSORS AND WARNING LEDS ( OIL PRESSURE AND FUEL PRESSURE )

CAN BE RE PROGRAMMED TO SUIT ANY APPLICATION, WAS TUNED AND AND MADE FOR ALL THE ABOVE ITEMS.

$1800.00

ITEM : WHEELS

R33 GTR WHEELS AND TYRES

IN OK CONDITION HAVE A COUPLE MARKS ON THEM

FRONT TYRES – 90%

REAR TYRES – 60%

BRIDGESTONE POTENZA

$850.00

ITEM : COIL OVERS

CUSCO COMP COIL OVERS TO SUIT R32 + OTHERS

GREAT COIL OVERS, HANDLING IS UNREAL AND SMOOTH

GREAT CONDITION, NO LEAKS

$1000.00

ITEM : DIFF

KAAZ 2 WAY

GTR DIFF COVER FOR EXTRA OIL AND COOLING

LOCKS UP LIKE YOU CANT BELIEVE

$850.00

ITEM : SEATS

R33 GTR FRONT SEATS

FIT IN 32 33 GTST

NO RIPS OR TEARS

$650.00

ITEM : CLUTCH

HKS TWIN PLATE CLUTCH AND FLYWHEEL TO SUIT RB20 BOX ( NOT SURE IF IT FITS OTHERS BUT THINK I WOULD )

LESS THEN 3000km ON IT

$1500.00

ITEM : N1 R32 HEAD LIGHTS

N1 HEAD LIGHTS, NO CRACKS

$450.00 PAIR

ITEM : R32 SHELL

I HAVE MY R32 GTST FOUR DOOR SHELL THAT HAS REGO UP FOR SALE INFO BELOW

SILVER, BODY IS A LITTLE RUFF BUT STILL PRITTY GOOD CONSIDERING ITS OVER 20 YEARS OLD

1989 MODEL

R32 GTR BRAKES AND SLOTTED ROTORS

HYDROLIC HAND BRAKE

ARC FRONT CASTER ARMS

CUSCO UPPER FRONT ARMS

CUSCO REAR UPPER ARMS

CEFIRO ENGINE X MEMBER ( ENGINE SITS LOWER THE STANDARD X MEMBER )

90% OF INTERIOR STILL THERE

99% OF ALL PANELS

HEAPS OF OTHER BITS AND PEICES

MINUS THE BELOW

NO ENGINE OR ENGINE RELATED PARTS

NO GEAR BOX

NO DIFF

NO ECU OR WIRING

NO SUSPENSION

NO WHEELS

NO HEAD LIGHTS

COUPLE OTHER SMALL BITS MISSING

$4000.00 INCLUDING REGO!

CONDITION : ALL ITEMS ARE IN GREAT CONDITION UNLESS OTHERWISE STATED

LOCATION : ALL ITEMS ARE IN ADELAIDE, POSTAGE AT BUYERS EXPENSE

CONTACT : PM ME

PICTURES : CAN MMS PEOPLE PICS

Link to comment
https://www.sau.com.au/forums/topic/340360-eoi-parts/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wish I had this advice when I did my pump. It went in and out 3 or 4 times, and on the last time it snapped.
    • Tried them, they leaked. I also foolishly bought some random rubber ones that leaked too.  Genuine and not looked back.    As always though sample size of one, and I could have made a mistake installing them. 
    • Technically still manual process to set it first time though
    • Shit job but not hard. I'd use a piece of wood to knock the plastic lid open to avoid damaging it, use a vacuum to clean up the fuel sender lid also so crap doesn't fall in. I'd probably do pump and filter at the same time since you're already in there, I reused my OEM sock after a quick clean since the one provided wasn't long enough. Could also hardwire your pump if you feel inclined.
    • Supercheap auto sell this: https://www.supercheapauto.com.au/p/pat-plusquip-fuel-tank-lock-ring-tool---universal-kit/SPO3564082.html I own this and if you HAVE PATIENCE you can remove it without snapping lines and generally being incredibly angry, then said at doing this job. Sadly I've removed the pump about 75,000 times over the years. I don't know if you're a large lad or a smaller lad but my advice to you as someone who is 185cm is if you are my height or smaller, is to sit in the boot and take your time. Yes you can put the seal on. The seal goes over the white thing/lid (you will see how it 'slots' in) then the whole assembly presses into the tank. then you screw the lock ring on. I spent so much time doing things the wrong way by trying to mount the seal into the tank first, then putting the white fuel hat on in the space provided. Put it together first then it'll all go in. But seriously be careful about removing the hoses AND where the removal tool is moving relative to the plastic pipes coming out of the lid when you've removed it. IT IS BRITTLE So brittle in fact I have two spare lids, and would recommend buying a spare and having it handy before attempting to do this. May as well throw https://justjap.com/products/deatschwerks-dw300-fuel-pump-nissan-s13-silvia-r32-r33-r34-skyline-c34-stagea?currency=AUD in the tank as well, as this uses all stock plugs and such. You may need to/strongly recommend you re-use your OEM fuel sock or use the one supplied with a length of hose so it sits at the stock height.
×
×
  • Create New...