Jump to content
SAU Community

Recommended Posts

Kakimoto full mega n1 3.5 inch pipes with larger tip, metal cat looks to be about 5 inch body,

looking for $700 can organize freight at cost. prob looking at $50 or so via courier to most capital cities.

not willing to separate the cat yet.. but will consider

post-31456-1287024153_thumb.jpgpost-31456-1287024176_thumb.jpg

post-31456-1287024197_thumb.jpg

Whiteline strut bars and adjustable sway bars for r32 gtr, and maybe gtst?? $700 for the lot (rrp over $1000) front sway included (not in photo.)

post-31456-1287024981_thumb.jpg

Bilstein adjustable Coil overs with eibach springs front and rear $900 (photo is rears only)

post-31456-1287024995_thumb.jpg

Located in Sydney

I'm guessing the exhaust is more suited to track use due to the size? How loud is it really?

Its got a cat on it :blush: would be fine for the street, they sound very good

am pretty sure this is the same one

pretty quiet when you want it to be, and loud all the other times.

What spring rates are these ?

I'm not too sure on the rates. but heres the part numbers done thru google on the eibach website.

front and rear respectively.

post-31456-1287303606_thumb.jpg

Pm's replied to!

Exhaust and Cat now $700 including freight to anywhere in Aus!

Coilovers still available, and strut braces still available!

Exhaust is now 600 + freight in aus or pickup in Sydney

A decent cat is half that price!! this is a bargain!

When all else fails its going up on ebay!!!

hey mate if your intrested in seperating bars im keen on the rear sway bar

Hey they sold last week on ebay. sorry!

Shocks have sold on ebay.... someone could have bought and turned a tidy profit here!!

Still Have exhaust... 2 more days then its up on fleeeee bay too! unless someone takes it away now..

Genuine 3.5 ID on the exhaust?

I am unsure that even exists!! usually they measure exhaust from the OD..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I do have their “Nissanie Motorsports Co.” vin plates, but I am curious if anyone would have more info on them. Like how many cars they’ve imported and whatnot
    • Been a long while since i have updated this money pit lol.  Have had a few tune related issues with the car, first blowing the frost plug out the back of the head and then blowing the headgasket 3 months later, which has now been retuned and sorted. Done a few little changes along the way as well, i wasn't happy with the wheel and brake setup, so start of last year i managed to get myself a set of r35 brakes and nismo lmgt4 18x10.5 +15 Upgraded to now running a Precision Gen 2 6870 with a 1.15ar, to be honest felt more like a downgrade as the car feels much lazier around town compared to the Gen2 6466 previously. 0761719E-5683-43F7-BD3B-4BD94335DFF4.mov
    • Hi there, i am currently using the Elmers Racing Billet merge collector, we are using sch40 tubing and 1.5" ID, no cracks so far. however if i was to do it again, i would go sch10 with 1.25" runners
    • I haven't touched the turbos so might need to look at that 👍 Appreciated 🙏
    • If you haven't replaced the OEM turbos, replace them sooner than later. I have seen recent pictures of what OEM ceramic turbo failure can do in an RB26 and it will make a 10k AUD budget look like a joke. Single vs twins have been done to death on this forum. If your turbos haven't fallen apart you can probably send yours off to Hypergear for rebuild. The journal bearing option will have more turbo lag but it's a good bit cheaper. I would probably go for ball bearing CHRA but keep in mind ball bearing turbos are more particular about oil pressure/flow.
×
×
  • Create New...