Jump to content
SAU Community

Recommended Posts

Date: Sun 14th Nov

Time:

Move in 9am-10am

Move out 3pm-4pm

This will be a static car display. You cannot come in later then specified, or leave earlier than specified.

Your car must be on display, and stationary for the duration of the Show'n'Shine due to the nature of the area and public safety requirements.

Location: Waterfront City, Docklands

Entry is via Pearl River Road - refer to map below for details, "X" marks the spot where Marshals for the event will be waiting @ 9am

There is a Tram Stop right out the front as well, Route 30 or 48

gallery_709_1130_88434.png

Car Limit:

A limit of 80 cars is the MAX for this event. Should we run out of room sooner (due to larger cars), we will have to close the gates.[/size]

Obviously, SAU-Vic Members only. Anyone from the public is more than welcome to come along and checkout the display, however you will not be allowed to enter your car.

All cars must be Road Registered. So no towing race cars without some sort of rego.

How To Enter:

Upon entry onto the grounds you will be greeted by one of our Committee members and given directions.

If you wish to have your car in the Show N Shine and be eligible for voting you must notify our team.

You will be given a "Vote for me" sheet to place on your car with your details upon arriving.

Prizes and Awards:

Trophies will be awarded for "Best in Show" in the following main categories:

• Godzilla class (32, 33, 34 GT-R, one for each) & Best overall GTR

• Godzuki class (31, 32, 33, 34 GTS/GTT one for each) & Best overall GTS/GTT

• WRC class (WRX, Evo)

• Dorifto class (Silvia platform)

• Intruder class (other)

Use of facilities:

The following must be adhered to by all Members attending the day

- Strictly walking pace for cars, hazard lights ON at all times whilst in motion.

- No loud engine revving, starting of engines once stationary, silly compressor nuisance noises.

- No unwanted behaviour on (or when leaving) the park grounds.

- No dumping of rubbish.

IF members do not adhere to the above rules, Committee may ask you to leave. Keep in mind the club will be in the public spotlight and stupidity will not be tolerated.

Other Info:

- Bring whatever you may require for the duration, seats, hats etc. There is no leaving once you are in position until the end time of the show.

- The Piazza has PLENTY of food/beverage stores around, you will not need to go far for any requirements there.

- And issues on the day, see the people in Hi-Vis vests immediately.

Any questions please post up - see everyone there.

Cheers

Ash

Link to comment
https://www.sau.com.au/forums/topic/340440-sau-vic-shownshine/
Share on other sites

  • Replies 168
  • Created
  • Last Reply

Top Posters In This Topic

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
    • Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...