Jump to content
SAU Community

What Offset Can I Get Away With?

NYTSKY

By NYTSKY,
in Exterior & Interior Styling

 Share

Recommended Posts

Craved Grand Master

Craved

Posted
Posted

Dave - im running 17x9 +22 all round, only just hits the stock guards unrolled with 245 tyres

running the +22 @ 10.5 would sit them 18.5 mm out from the inner lip edge - you should be able to fit them no problem with rolled guards

joeyjoejoejuniorshabadoo Grand Master

joeyjoejoejuniorshabadoo

Posted
Posted

ima do this visually so you can get an idea :P

as compared to my car with the professors on it, those offsets will sit 10mm in on the fronts and 16mm out on the rears

(prof's are 9.5+25 all round)

med_gallery_36777_3194_134461.jpg

imho you would be best going for the 18x9.5+12 on the fronts and 19x10.5+22 as the staggered 18/19's looks hawt :)

otherwise you could go 19x9.5+12 on the fronts of you don't wanna stagger

this will give you 13mm more front and 16mm more rear than in the above pic

and re: the 18/19 stagger... i give you...

MattS15-09.jpg

athid's old s15

Jap_Muscle Mentor

Jap_Muscle

Posted
Posted

not sure what differences are between the r34 and r33 guards but im running 9.5" +24 and had to lip and slightly flare (nothing major no paint cracks) to have them sitting about 3-4mm out of the guard. looks tough ill take a pic in a few minutes and post up.

tyres play a big part in deciding so you should really really consider tyre profiles as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • hardsteppa
      R-chassis INNER tie rod torque spec?

      By hardsteppa · Posted

      Don't be ridiculous. "2-3 ugga duggas or one Oof. You have to use Oof on tie rods because you can't get an ugga dugga on there." Is not helping the guy at all.
    • JC71
      gauge needle removal

      By JC71 · Posted

      I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Roy
      A Boy's Love For His Rb20

      By Roy · Posted

      Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • GTSBoy
      gauge needle removal

      By GTSBoy · Posted

      Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • GTSBoy
      Wheel refurb?

      By GTSBoy · Posted

      Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
×
×
  • Create New...