Jump to content
SAU Community

Auto And Manual Rb25det Computer/loom Different?

Ad's

By Ad's,
in Engines & Forced Induction

 Share

Recommended Posts

Ad's Mentor

Ad's

Posted
Posted (edited)

Gday guys i have had a look around trying to find my answer but i haven't found much that helps. Are Auto RB25DET computer and or loom different to manual computer/loom? As I'm trying to wire in my 25 into the coupe and the wire colours are different to what it's telling me. If they are different can someone please point me in the direction of a pin out diagram for both as well as ecu wire colours.

Thanks and sorry if this has been covered before.

Edited by KDS_HR31
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Computer is different - doesn't matter if being used in a manual

The looms ... Hmm knowing Nissan it would be the same in theory as usually its one loom suits all.

But I could be wrong there on that one.

Ad's Mentor

Ad's

Posted
  • Author
Posted (edited)

Ahh ok thanks mate.

Anyone got any pin out diagrams or know that the loom that goes to the ecu is different? Also its a s2 motor if that makes any difference or helps anyone.

Edited by KDS_HR31
  • 6 months later...
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

The pinouts for R33 and R32 are very similar. (R32 doesn't have boost solenoid - pin is used for something else). Should be able to find any pinouts you want fairly quickly on Google - some have colour codes for wires as well.

muchogarcia34 Collaborator

muchogarcia34

Posted
Posted

Yeah ECU is the same and the loom is a little different but still works. The only thing you have to change is the wiring going to the gearbox but if you can get a piece of the manual wiring loom for the gearbox you can simply unplug the auto one from near the fuse box and plug the manual one in and all will be good.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Rear subframe stay bracket bolt removal issues

      By MBS206 · Posted

      TBH, it sounds like the threads on the bolt are fubar in a specific section. Most likely as you've been working it back and forth it has torn threads out, as you loosen the bolt, this section enters the nut, now you're spinning a round shaft inside the nut, there's no threads here.   Use something similar to a claw on a hammer that will fit either side of the bolt head and try to apply downward force while also undoing it. The idea is to attempt to catch a thread, or just rip the f**ker out. Caution on ripping out, as it could bend/maime/mangle what the captive nut attaches to. If the captive nut is actually okay, you could do the dirty part of cutting the head off the bolt, then cut a slit in the end of the thread that's now exposed and then screw it up and into the area the captive nut is until it falls out the other side. However, this does risk the remainder of the bolt rusting over time and damaging near the captive nut and also making it rust. However, so can cutting pieces of panel work out to access this area if you don't reseal it properly.
    • MBS206
      Rb25 det nitto washer crank gear

      By MBS206 · Posted

      Well, every piece of information on that part when you track it back to Nitto says it's for a KIT of theirs. It is also designed thicker to be stronger. And they speak about a specific harmonic balancer bolt they supply for the whole setup.
    • MrStabby
      Rear subframe stay bracket bolt removal issues

      By MrStabby · Posted

      Techniques for removing stuck bolts are: hitting the bolt head with a hammer, heating the bolt to red hot then letting it cool and working it back and forth like you are already doing. AFAIK the idea is to try to crush whatever material is stuck between the threads (and heat also melts locktite but that's almost certainly not relevant in this case).
    • GTSBoy
      Rb25 det nitto washer crank gear

      By GTSBoy · Posted

      Yuh, I think it works with the Nitto gear only. I presume that you're not also using the Nitto gear? Watch the video. Compare the interface between the Nitto gear and washer (on the gear side) vs the stocker and decide if you think the Nitto gear is different from stock there.
    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Liking the new charger, battery all good (I think).   Also like how you can put it in power supply mode too. Will troubleshoot with that sometime soon.
×
×
  • Create New...