Jump to content
SAU Community

Recommended Posts

Hay guys Looking at selling my GTR.

Dont really drive it anymore and i feel its wasted.

Everything about this car has been upgraded, Super Fast car with heaps more potential, power has been limited to 350 hp while the engine is fresh, engine and components have only done 5000klm with the gearbox and diff doing a bit more with 15,000 klm. The Car runs a Garret Ball Bearing TO4z high mounted with full 3.75" HKS exhaust (Very Quiet) with a high flow 3.5" cat, has upgraded fuel system with 780cc injectors being feed from a custom twin entry fuel rail, fuel is pumped by a bosh 044 pump and is regulated with a Sard Fuel pressure regulator. The engine is controlled by a VIPEC engine managment system tuned to 15 psi by Mark Jacobson From Godzilla Motor Sport. The car has a full respray in Pale Blue Effect (From 2006 Toyota Corolla) and a standard gtr body kit (not including the wing). It has a Kenwood 7" fold out DVD player and alpine V12 amp with fusion speakers. The Wheels are FZERO Special -Volk rays 18" x 10" and are wrapped in falken 275,35,18. The Suspension is Tein hight adjustable and quite stiff. 4500k Full HID Xenon head light kit has just been installed.

A Full List of Mods and engine work that has been carried out can be emailed to any one that is more interested.

All Offers Considered.

Car can also come with defi boost gauge. Also has a trust extended sump and r33 gtr front diff, currently not on the car but can go with it for a small price.

Im asking for $22500 ono.

Ive spent alot more than that on this car but its time to move on.

You can email me at [email protected]

Or PM me....

post-38590-1287906798_thumb.jpg

post-38590-1287906928_thumb.jpg

post-38590-1287907029_thumb.jpg

post-38590-1287907072_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/341666-r32-gtr/
Share on other sites

  • 3 weeks later...
  • 3 weeks later...
  • 2 weeks later...

Hay bud, will get some more pics when i finish putting the cooler and piping in.

running 350hp atw,, that was the run in tune, but pulls harder than that now,

if you want full specs i will email it to you.

PM me your email

Link to comment
https://www.sau.com.au/forums/topic/341666-r32-gtr/#findComment-5659675
Share on other sites

  • 4 weeks later...
  • 4 weeks later...
  • 7 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This is the clearest explanation out of those: Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension. Basically you turn the engine with the tensioner bolt loose, then use the allen key to hold it while you torque it up. And yes after that a good guide is being able to twist it 90o in one of the long free lengths of the belt
    • good choice....I have a set of those and use them all the time including on this job. Plus, no-one wants a damaged nipple
    • Thanks all, went with nismo strengthened belt and all genuine nissan idler and tensioner Question on RB25DET Neo Timing Tensioner: I have a question about the RB25DET Neo timing tensioner. In one of the videos (minute 20 of https://www.youtube.com/watch?v=17y37BB9xnA and minute 27 of https://www.youtube.com/watch?v=Pb99s2E9xUg), the process suggests tightening the tensioner pulley installation bolt to the specified torque initially, and then loosening it slightly to allow the spring to set the correct tension. Is this the correct approach? The R33 workshop manual on page 74 states: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. The way this is written is confusing. Does this mean: Undo the nut, then reduce the tension by turning clockwise? Snug the nut so it stays in position without applying tension to the belt while removing the timing belt? The manual wording makes it sound like the nut will tighten automatically when you turn the tensioner clockwise , which is unclear to me.   Timing Belt Tension Adjustment Process: After loosening the tensioner nut, you turn the engine two full rotations by hand, which should set the correct tension. Once the tension is set, you tighten the bolt to 43 N·m (4.4 kg·m). Before tightening, you need to insert the Allen key into the hexagonal hole to hold the pulley in place while tightening the bolt. In one of the videos, it’s mentioned that you should twist the belt side to side, or turn it slightly to check if the tension is correct. The belt should turn halfway, indicating the right tension. However, I know that twisting or turning the belt is not a good idea. What are your thoughts on this? Finally, how can I ensure the belt isn’t overtightened? I’ve seen many cases where people have overtightened the timing belt.   Manual Excerpts: Page 74: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. Remove the timing belt from each pulley. Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension.
    • Takes a few minutes to malke one. Wood, or steel, or a wrap strap with some strategically placed solids to provide teh drive onto the ribs.
    • I would strongly suggest using the correct tool. They are not expensive and make the job much easier and don't damage the lock ring. Google "fuel tank lock ring removal tool" to see what I'm talking about. 
×
×
  • Create New...