Rb30 Engine Pics

[waxracing]

Here is my rb30

getting there and close to going in the car

[r33_racer]

Heres our RB30DET in the race car.

[rockabilly]

waxracing, tell me you are going to put another tensioner/idler on that cambelt before you install it..

that will be fun in a rear wheel drive car.lol

Edited January 22, 2011 by rockabilly

[waxracing]

Yes I am. Its not finished yet

[mild r33]

My RB25/30. Still want to tidy the engine bay up abit bit, but it works..

Edited January 23, 2011 by mild r33

[Single]

I'm starting to tidy up my silvia's bay... but it is tight in their.

[t04z]

here's a pic of my baby haha its been 7 months in the making so far but its getting close now put on manifold n sump the otherday, gee making an oil pickup was a prick took me hours to get right it better work lol

[R32Abuser]

Not 100% complete. Still having issues with the tune etc. as per my thread...

Objective was to make it look as stealth/clean as possible. Will probably end up going a stock route Blitz cooler down the road to make it look standard as possible.

Who woulda known there's a GT3076R lurking under there

Edited July 30, 2011 by R32Abuser

[045HOW]

Not 100% complete. Still having issues with the tune etc. as per my thread...

Objective was to make it look as stealth/clean as possible. Will probably end up going a stock route Blitz cooler down the road to make it look standard as possible.

Who woulda known there's a GT3076R lurking under there

very sneaky all round. thats one powerful RB20

[the_jack]

have done a bit more since then

Edited August 3, 2011 by the_jack

[bubba]

Not really a picture but you get the idea..

Edit: it won't preview

[045HOW]

Not really a picture but you get the idea..

Edit: it won't preview

f**k yeah! post more vids of it being driven and such!!

[bubba]

f**k yeah! post more vids of it being driven and such!!

ok ok

Not tuned yet, only running 10psi but safely rich (dips to 11s and sometimes high 10s) and no ping ping. Doing a bit of a shakedown and sorting out a few issues (car has been off the road for 18 months) before I chuck it on the dyno and wind the boost up

[sriver killer]

Ah. just thought I would throw some pics up.

Only just running in , done 500kms so far so gud!

done what I believe is the absolute MINIMUM for a reliable build. + I threw in some old engine building skills cause I have got alot of spare time.

Brand new 25 oil pump

crank collar

Blueprinted complete bottom end.

Removed all casting flashes in block, crank, rods,

Polished, streamlined crank and rods

Balanced complete rotating assembly

New cast pistons (standard pistons so 8.3:1 comp)

oil restrictors 1.5MM(both)

opened up oil returns

got a good set of rings on my 3rd box , NPC rings were too tight, Hastings rings were all consistently 10 though too large, found the happy medium with acl rings.

Nissan bearings

mls head gasket

arp head stud kit + rod bolts

std cams + mild port job to head.

Remove casting flashes, imperfections, port matched to both inlet and exhaust manifold.

CC combustion chambers

Internal vct mod

Helicoiled every single thread on the exhaust side.

6boost, , plazmaman, 3076R.82Rear ext gate and 3.5inch turbo back.

only at run in stages, big difference in torque between this and the standard 25 that I had in place.

can't wait to get it tuned!!!!

[TiTAN]

having had my pod where yours is before, you will notice an improvement in power if you get it away from there and into the corner where it can get non radiator/exhaust manifold heated air.

[sriver killer]

having had my pod where yours is before, you will notice an improvement in power if you get it away from there and into the corner where it can get non radiator/exhaust manifold heated air.

Ive gone from having the pod in the corner to having it smack bang on the turbo.

Maybe because its winter(/end) but I haven't really noticed any difference bar the throttle response.

didn't change my mph down the 1/4 and sounds/looks alot better.

having said that, I will probably do back to back on the dyno and post them up