Jump to content
SAU Community

Eboost Install Need Help

evlwog

By evlwog,
in Engines & Forced Induction

 Share

Recommended Posts

evlwog Enthusiast

evlwog

Posted
Posted (edited)

Hi guys,

Just installing the e boost street into my r32 gtr and have come stuck on where to connect the solenoid hose's.

Do I disconnect the STD solenoid hoses and use those and if so which would go where ?

Or do I leave the STD solenoid and run separate connections ? And if so where from ?

Sorry if I'm asking something that's already been answered but I have searched through the forum and not found anything.

So any help would be awesome thanks guys.

Edited by evlwog
Link to comment
https://www.sau.com.au/forums/topic/342505-eboost-install-need-help/
Share on other sites
evlwog Enthusiast

evlwog

Posted
  • Author
Posted
follow the vacuum diagram that's posted for rb26, remove solenoid altogether, and keep ur eboost solenoid as close as u can near the actuators without heat becoming an issue

Thanks dude, I have tried to find the vacuum diagram no luck :ermm: would disconnecting the STD solenoid throw a fault code ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By TurboTapin · Posted

      Do the following first and get back to us. - Clean and verify your IACV - Verify for vacuum leaks/post MAF leaks. (Pressure test is the best and cheapest way) - Do you have a BOV with stock ecu/MAF? If so, remove it.     
    • DRoc81
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By DRoc81 · Posted

      Hey all, The skyline I have is stalling when the engine is at normal operating temp.  When starting it while it is cold, it'll run just fine.  I have replaced the battery (bad cell), I have replaced the fuel pump, fuel filter and clean the MAF sensor.  Any other suggestions?
    • DRoc81
      Shifting questions

      By DRoc81 · Posted

      Thanks for all the information on this.  I tried ordering the parts from Amayama website and all 3 Solenoids are discontinued and not available.  Does anyone have any other websites to suggest that I could find the parts?   Separate issue-- I will start a new thread, but basically the vehicle is stalling when warmed up.
    • TurboTapin
      RB25DET Solid lifter conversion

      By TurboTapin · Posted

      It's unfortunate what Tomei USA has done to Tomei's name in general. I'm very weary of ordering parts from them now. I only order direct from a Japanse source (e.g Nengun). At least their logos are different, so you end up knowing what you have. 
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Update Issues 5 (plus #4) - 10 After making a claim about issue #4's missing part, DeAgostini Japan sent a whole new issue #4 and it arrived about 2 weeks after that. That was back in early March. It took another 4 weeks to receive issues 5 - 13 though. This update is for issues 5 - 10. Ove the 5 issues the front left suspension and most of the engine have been completed. The quality of the castings and fit of the parts is quite good, it seems better than DeAgostini's BNR34 Skyline GT-R from the Fast & Furious 2 movie, which (to me anyway) doesn't seem to have as tight tolerances or quite as accurate castings.  Each issue has a lot of info about the 1989 - 1993 Skyline range and other Nissan models from that era, but the focus is on the BNR32 Skyline GT-R Nismo and the various racing it did in Japan, Europe (Spa 24hrs) and of course Australia. I've included some text translated with Google Lens in some photos and will add to them if there's anything worth including. 
×
×
  • Create New...