Jump to content
SAU Community

Lakeside


handbrake
 Share

Recommended Posts

sure would love to get down into the 55's! no easy task. I need bucket loads of track time.

I will head out there on the Paul Stokell days but he only runs a few events out there every year. seeing as I can only get out on the track on weekdays normally, which track events should I get to? I see trackattack has some weekday lakeside days in their calendar but have never attended one of their events. any others I should try? would love to get out there once a month and out at QR once a month

Hi Mark,

Porsche club as you know also do track days at Lakeside, but most likely on weekends.

I think the time spent on Paul Stokell track days is quite valuable. He is a Lakeside expert. Especially with your permance monitoring, having Paul do at least one session in your car around the track for you to later analyse and overlay with your sessions is the smartest way to go. Then it is like everyone else says its bum in seat time on track and slowly chipping away at it.

With some areas that I am working on- I asked him yesterday - Do you think we could go through the kink flat out and he said ultimately yes but there would be no room for error. He advised at least a dab on the brakes before turn in for some forward weight transfer. Im also working on the back half of track and trying to reduce understeer through the second last corner.

I like this quote from "Lakeside Introductary Racemeeting":

"As every one who has raced there will tell you - Lakeside is a DANGEROUS place. Do not interpret this as a dare. Many people have come to grief at Lakeside and some of them terminally. It is NOT a place to take unnecessary risks when racing because it will bite you and hard! "

Link to comment
Share on other sites

One issue with lakeside in general that it is getting just too busy.

It can be quite scary and dodgy sometimes, with what is a small and narrow track with 20+ cars out in a session with VERY big variables in both car speed and driver understanding. The y DO attempt to group cars by lap times but I think quite a few guys tell porky pies to feel better about themselves!?

eg; Having a 997 GT3 outblast you on the straight and gap you 100 metres only to come across him under the bridge, previously unseen, with a speed differential of 40/50klm/h, when you're fully loaded up, maximum commitment, doing 200 odd with the wall a metre away on the outside. Shit like that never gets old! :P

Link to comment
Share on other sites

Bastards!!

170 down the straight if I'm lucky

Bridge? Well at least I'm in 5th, but I''d be lucky to be much over 150 there :)

Then again, you guys are over 10 seconds a lap faster than me

Still, at least I can claw back some of that advantage on gravel (where it counts) :)

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Latest Posts

    • Much less twat-tastic. CF wheels are too garish for civilised use.
    • From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...