Jump to content
SAU Community

Recommended Posts

i wonder if they do "wood slicks" :bahaha:

My tyres went Bam! :bang:

so theres that cost ..... and the amount i owe to the coppers $600 ..... while im still paying off the engine rebuild $6K ..... and my rent etc.

  • Replies 62.7k
  • Created
  • Last Reply

Top Posters In This Topic

  • chaos

    7164

  • Ska

    5791

  • BelGarion

    3645

  • Nexus9

    3590

Top Posters In This Topic

i wonder if they do "wood slicks" :bahaha:

My tyres went Bam! :bang:

so theres that cost ..... and the amount i owe to the coppers $600 ..... while im still paying off the engine rebuild $6K ..... and my rent etc.

How did your tyres go bang ..... if you can't drive for 3 months ..huh...huh?

I'm starting "Tsunami Cappuccino Appeal foundation - Your gift today will rush turbo and boost Survival Kits to Cappuccinos affected by the typical tsunami waves of ricers and bogans, and provide other speed up parts as needed."

i wonder if they do "wood slicks" :bahaha:

My tyres went Bam! :bang:

so theres that cost ..... and the amount i owe to the coppers $600 ..... while im still paying off the engine rebuild $6K ..... and my rent etc.

indeed u can get wood slicks with those polished and glazed paint :D

I had tyre blew when I parked my golf on side street to answer stupid werk call, 2hrs later I showed up at werk with brand new tyres :)

nope on the outside they were baldish ...... on the inside they were down to the canvas ...... they just had enough and gave up :) Luckily while we were slowing down at the lights and not an hour beforehand where we were having some country backroad fun.

Nobody noticed they were balding.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Sharing results from recent Liberty Walk R35 GTR, since they are still considered as somesort of a V36 Skyline. We do them turbos too. This are high flowed SS-1 models with ball bearing conversion done.  Car have managed to pull 485awkws @ 20Psi so far pushing limitations of factory built engine. The build list for R35 GTR enthusiasts as follow : HyperGear high flowed stock turbos in SS1 (G25-660 specs) Custom titanium intake pipes. Vspec performance titanium front pipes. Vspec performance 4" titanium exhaust. Upgrade fuel pumps. 1200cc injectors. Ignition coilpacks Hks intake plenum. Hks intercooler piping. Greddy intercooler. Greddy bovs. Top-secret coolant reservoir. Emtron ecu. Straight E85. Built gear box.  
    • Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
×
×
  • Create New...