Jump to content
SAU Community

Recommended Posts

I should be getting the 31 at least tomorrow night.. but its going to need a few things done before its on the road. The diff replace is going to cost a bit more than i thought, so 'project get skyline same colour' may have to be on hold for a few weeks.

  • Replies 62.7k
  • Created
  • Last Reply

Top Posters In This Topic

  • chaos

    7164

  • Ska

    5791

  • BelGarion

    3645

  • Nexus9

    3590

Top Posters In This Topic

evenin' all,

Question about the hybrid intercoolers....why does everyone shitcan them???

I have been looking around for some bad reviews, but can't seem to find much info at all. What's the go...are they leaky? poorly made or what?

Or is it the fact that they are manufactured in China?

Anyone got a definitive answer or is it all just heresay?

Hi Warrick

yeah I would like to know too.

When I was discussing with Gavin Woods the future mods for my car in regards to the power I want to acheive, he said not to touch the Hybrid as it didn't flow well enough for high powered cars.

He said it was good for up to 200KW but after that it just doesn't cut it.

So consequently I am madly saving for a new Trust intercooler

Hmmmm....Ok, well from what I have read on this forum, Gavin knows his shit.

So these "Hybrid spec" intercoolers (apparently made in the same factory), such as the ones mindflux is trying to do a group buy on are essentially the same thing I presume, and in that case to be steered clear of.

the hybrid coolers are fine .. ive got one on the way, however if you wanna run high kilowatts, then you best go for something more expensive. i dont plan to hit 200kw so i feel one of these coolers would be perfect for me.

other peopple bag them because there cheap they assume 'if their cheap its shit; .. other people jump on the band wagon 'oh wasnt made in japan must be shit'

yamutha - im not 'trying' to do a group buy .. i have already got mine ordered, infact ive had it eveb before the group by .. i was just letting people know about these intercoolers as i know there is alot of people after these intercoolers.

baah ill explain after i get away from the TV

bbs

200kw is all the hybrid can cope with ? even the stockie can do better than that most of the time.

for up to 300rwkw or so even the GTR cooler is all you need.. "all over again".. GTR cooler, custom stainless steel piping.

Generally the Trust I think is "the" best regarded cooler in japan.. the others come somewhere after that.. HKS isn't bad either, although i'm biased :rofl:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 馃槕. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
    • Hey everyone, This is my first post apart of the introduction. I tried searching a bit on the forum but couldn't really get a straight answer. I got the car to my mechanic as I felt it being weak. It seems that it was missing on two cylinders due to the injectors. I had all my injectors clean and the car runs much better. The mechanic also confirmed my suspicions that the cat is clogged and needs to be tackled asap. The cat rattles a bit and the hot exhaust warning frequently lights up when driving after getting the injectors clean. In my introduction I was asked about what modification I might be interested in and mentioned a cat delete. From what I was told, this is not really beneficial on the RB20DE and there are more cons than pros.  Could perhaps anyone give some suggestions on what the best course of action would be since the current cat is toast and needs to be removed/replaced anyway? I can also sometimes smell a strong smell of fuel, but I'm not sure if this is related.
    • Hope the cans went down well at least 
    • 255 can't go wrong with the price.
    • When I was replacing my pump due to being stranded in the wrong state, I went with the Deatschwerks 320lph kit. It is a direct plug in to the stock wires, harness, everything. It comes with a plug... but you can plug the OEM plug directly into this thing. https://justjap.com/products/deatschwerks-dw300-fuel-pump-nissan-s13-silvia-r32-r33-r34-skyline-c34-stagea?currency=AUD Downside: Won't actually flow that much on boost if you want to push it on E85, but it's comparable to the 040/255 etc. Little more actually.
  • Create New...