Jump to content
SAU Community

Recommended Posts

  • Replies 62.7k
  • Created
  • Last Reply

Top Posters In This Topic

  • chaos

    7164

  • Ska

    5791

  • BelGarion

    3645

  • Nexus9

    3590

Top Posters In This Topic

Belg and Nex will be quickest...

 

Ska and me will be next...

 

MJ will be last :)

 

Warwick will probably wimp out...

NO SKA WILL be last, I am ALWAYS last, got used to it though :D I tend to pick on cars I know I can beat, like falcodores :)

Belg and Nex will be quickest...

 

Ska and me will be next...

 

MJ will be last :)

 

Warwick will probably wimp out...

lmao...If I can muster up the funds.....I will prolly run a close last :D

today has kinda drained my funds....but the missus' credit card is in sight :)

Yeah I did have 2 passengers, 3 jacks and a big ass backpack in the boot :) well I am using that as an excuse, not the lack of a decent exhaust, fmic, ebc, etc etc etc

I had my golf clubs in the back, does that count? :D

Hey JL you bringing out the gtr to play tomorrow night??!?!

Yeah, I was going to bring the GTST but the GF using that at the moment so I would have to wait for her to finish work. Would be nice to lay down some times while the GTR is still stock.

I am running as close as I can to stock tomorrow, so Ska may beat us all

ABBABAhbah ahaH ha h Aha haH aH aH aH aH ha aaaa :) maybe in a couple of years when I eventually stop hitting traffic islands and am able to afford a exhaust, but by then everyone will prolly have GTR's :D

Yeah, I was going to bring the GTST but the GF using that at the moment so I would have to wait for her to finish work. Would be nice to lay down some times while the GTR is still stock.

Yeah bring it on out, I want to see it in action :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The jack pad placement always had me scratching my head. I only have a small section to work with on both the E90 and E70 (and insert new project car here ) and I could see lining it up to be a bit of a bugger. For me, the E90 is just too low and needs small ramps and then the front centre jack point is a bit tricky to line up (it's half way down the subframe and about the size of a tennis ball, its really hard to see unless your head is on the ground), so I definitely like the idea of not having to do a multi-stage jack and just sliding these bad boys in under the sides. There's only one small point at each corner, so I can't jack AND add a stand on the same corner. Or, maybe I can and I'm too nervous to try. 😟
    • Is this not the biggest deal of all? I was hoping the whole "will slide under cars with skirts etc and lift evenly quickly with minimal fuss" was the entire point of such a device? 
    • Here's Neil's car up on mine recently
    • Yeah I've got one of these, Quick Jack not Quick Lift, but your link looks like a good copy For me, it's better than no hoist, but it is definitely not as good as a hoist  It lifts the car about 60cm which is a nice working height compared to regular stands and it is only under the sills so it doesn't get in the way like regular chassis stands do.  No need to use regular stands, it has a safety lock on it. On the down side it is really heavy/unwieldy to drag into place, and you have to place it after the car is there (no option to drive the car to where the frames are. You need to try and line it up with the proper sill points which is hard as it swings up in an arc and there is surprisingly little adjustment in the distance between the rubber pads for different car lengths. Not a big deal, but in practice a jack + stands is probably quicker. Also there are hydraulic lines to each side and you need either a 240v or 12v source to power it depending on which option you have, I use 12v as I always seem to have a battery around.
    • Finally addressing my catch can and oil setup Plan is to do as much as practical without having to remove the motor or pull it apart. (no back of head to sump drain/breather or oil restrictors) First step is a set of full length baffle plates from Hypertune and a Tomei cam cap stud kit. I could probably have laser cut and bent up my own ones but this took any guess work out
×
×
  • Create New...