Jump to content
SAU Community

Turbo Upgrades

gach2

By gach2,
in Engines & Forced Induction

 Share

Recommended Posts

gach2 Proficient

gach2

Posted
Posted

hey

not really looking at big power

aiming for 200rwkw

on a r33 rb25det

atm got a fmic

full 3 inch exhaust (no high flow cat due to previous epa)

everything else is standard

was planning on boosting the as it is to around 12 psi and though id come pretty close to acheiving what i wanted

though have been warned by a few people not to on a standard r33 turbo

due to the ceramic wheel

and have been told if wanting a cheap upgrade

to get a r34 turbo or a vg30 turbo

is this right?

and if so what is a vg30 turbo?

im guessing these are standard turbos used on vg30det hence z31 300zx (all i know that is single turbo), would this be an upgrade as it is, and would this straight bolt on a rb25det?

same with the r34 turbo

thanks

Link to comment
https://www.sau.com.au/forums/topic/343351-turbo-upgrades/
Share on other sites
Marcus89 Proficient

Marcus89

Posted
Posted

Only reason to go the r34 turbo is if your highflowing realistically otherwise it's too much cost for too little gain. Even for highflowing i would just do it to the turbo you have.

But as Nismoid said you will get 200rwkw out of the turbo safely

Link to comment
https://www.sau.com.au/forums/topic/343351-turbo-upgrades/#findComment-5536414
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      Skid pans in/around Sydney?

      By The Bogan · Posted

      Dragging some reo behind a ute or trailer will smooth out a dirt road, I've used reo a few times to do unsealed road maintenance when we didn't have any plant available  It's best done when the dirt is wet though, and then you just let it dry out for a day to harden up For wetting the dirt I've used some 44 gal drums in a ute or trailer, and a water pump connected to a hose with a old sprinkler tied to the reo to wet the material down whilst spreading Basically just drive slowly up and down the road a few times dragging a few sheets of reo wired together with the sprinkler wetting it all down as you go
    • The Bogan
      Skid pans in/around Sydney?

      By The Bogan · Posted

      I did a motokhana years ago with ??Sydney Sporting Car Club???, it was on a grassy paddock and was heaps of fun, I think it was north west Sydney IIRC The old R33 boat was covered in grass and dirt, but nothing that a good wash and detail didn't fix And thinking back, when SAU did the airstrip run in Goulburn years ago, where the old 33 won highest RWD MPH, the quickest RWD ET on the airstrip, and best paint IIRC (before the runs down the airstrip) the damage to the rear quarters from stones flicking up required them the get a respray  I would definitely do a grass motokhana again in the MX5 Who knows someone that owns a farm with a big empty paddock  Liability these days is a big issue though
    • Trilbyte
      RB25 S2 Idles but doesn't want to rev

      By Trilbyte · Posted

      No intention of driving the car the way it's set up now, just wanting to make sure I haven't made any mistakes along the way so that the tune can go smoothly, I don't want to waste anyone's time with stupid issues. And of course I intend to get it towed to the dyno in a completed state 😅 I have the base fuel pressure with the vacuum disconnected set at about 40psi, which I believe is at least relatively close to stock fuel pressure, maybe I'll have a fiddle with the reg and see what happens. For all I know I could be wasting my time with this and I should just plumb it in and see what the tuner reckons. I just find it a bit strange that it seems to be under so much load just free revving, but maybe that's just a result of the turbo slowing down the exhaust gasses and making a restriction in the flow, with no boost to compensate.
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      The boy just hit up google translate and it worked a treat, he said step one was "please urinate with precision and elegance", he then sent me the correct translation  I get some new loctite for the small fixtures tomorrow and get some "dort" going after that 🤣
    • Kinkstaah
      RB25 S2 Idles but doesn't want to rev

      By Kinkstaah · Posted

      Right, so is the fuel pressure the same as it was previously? If not, well, it's not going to work well. I can understand the theory I assume you are going for, which is: "Run it N/A, and if I have the original AFM, and same amount of fuel and intake air as previously, the fact there's a turbo in my exhaust should still make it run" Which it... might? Provided you don't actually change how much air or fuel is going into the car.. or getting out. But if you have changed that, all bets are off. What is the purpose to even have the car run this way? To get it to a tuner? And if the goal is to limp it to a tuner, you're still going to what - plumb up a whole intercooler system and new intake in the parking lot out front before your tune......?
×
×
  • Create New...