Jump to content
SAU Community

Recommended Posts

Hi People,

All items located in Sydney - Epping.

Post ok if buyer organises OR can deliver certain items

Contact any time -

PM on here

Cris - 0403491735 Call or sms

Adrian - 0413208919 Call or sms

Photos on request - inspection welcome any time!

WE NEED ALL OF THIS GONE! NO REASONABLE OFFER REFUSED!!!

Willing to trade for items of interest including (cash either way depending on item and condition) -

Front facing RB25DET intake manifold.

Bride Seat + Rails.

R32 Half/Full Cage.

Wheels of interest.

Genuine GTR front bar cover.

RB25DE SII

Complete engine in great running cond.

Came off a Stagea.

Comes with manual R33 ser2 ECU.

Comes with front AWD diff - You can change to RWD very easily and sell the FWD diff.

Never skipped a beat, ever.

Only top fluids used.

Regularly serviced.

Did a compression test before removed and showed to be very healthy engine.

$700 ONO

RB20DET Head

Complete head, has a small weld on one side so selling as is for cams, cam gears etc

Must go, need the space!!!!

$150 ONO

R32 GTS4 Front Diff

Comes complete with sump assembly and diff housing.

4:3 ratio!! Perfect for lowering your GTR diff ratio

Working perfect when removed from car.

Barely used as car has been often run in RWD mode.

$500 ONO – MUST GO!!

RB25DET Block

Needs oversized pistons - been bored out

Bores in good condition, no scoring etc.

Comes with everything except pistons.

$100 ONO – NO REASONABLE OFFER REFUSED!

R32 GTS4 Manual Gearbox

Reasonable condition.

Comes complete with transfer case

2nd gear has usual R32 uneasiness to shift into when cold only.

4th gear had a little bit of a crunch when shifting into at high RPM, otherwise fine in normal conditions

$400 ONO

R32 5 Point Roll Cage

Alloy.

Great fit.

Very light

Painted black

$300 ONO

R32 4door aftermarket (fibreglass) rear bar

Unpainted.

Small chip on corner edge near wheel arch.

$200 ONO

R34 Front Cradle + Rack

Very Good condition

Offers

R32 Motorised Lower Lip

Motorised lip that lowers above a certin speed.

Or you can lock it down to make your car look more low, and raise it when need be, driveway, speed bump etc.

Comes with everything you need, motors, lip etc.

Offers - NEEDS TO GO!

HKS Style SSQ BOV

In Fully hektic chrome.

$50 ONO

GTR Fuel Pump

Comes complete with sender and everything. Bolt in job

$75 ONO

GTR R32 Intercooler

Slight damage to a couple of fins

No leaks

Will hold boost no probs

No restriction to airflow

Offers - MUST GO!!!

R33 Airbox

Complete

RB25DET

$200 ONO

GTR R32 front drive shaft - From transfer case to front diff

x2

Worked fine

$50 ONO

Stock GTST Fuel pump

Complete.

Worked fine.

Direct bolt in.

With sender

$20 ONO

Stock Turbo exhaust manifold

$20

Clutch Fan with clutch coupling and R32 fan

Worked fine

$80 ONO

Air Conditioning Compressor

Worked fine

$80 ONO

Space Saver Wheel

Heaps of tread

Un used.

Brand spankers

ANY offer

Alternator

Perfect working condition

$50

Attessa pump

Worked fine.

$50 ONO

R32 GTST/GTS4 fuel tank

+ Tank straps

Been slightly pushed in but NO LEAKS

$20 or a case of beer. - Preferably not a $20 case of beer :blush:

I'm interested in the space saver wheel.... I'll give you $50 for it plus postage.

PM me if you're interested.

Hey Cris

I might ring you about this tomorrow, but do you have your old GTS4 4wd tailshaft? As I assume your running a rwd tailshaft now? I am in dire need of one.

thanks

  • 3 weeks later...
  • 2 weeks later...

hey there i was woundering if u hav any pics of the R32 Motorised Lower Lip at all and how much would it b to post it to adelaide

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I would paint match the whole thing to avoid unwanted attention  I had a similar bonnet, paint matched, on my old R33 GTST, but mine was a fibreglass jobbie made by Blitz in QLD, they work extremely well for radiator efficiency and under bonnet temps
    • Does anyone run this kit with factory plenum? Does the adapter and bosch tb fit under factory strut brace? I wanted to get this setup before going forward facing manifold. Thanks
    • small update time, after always wanting a "cool" looking bonnet for my car and always struggling to find one for the series 2 that i liked and wasn't an insane amount of money. Saw one i liked on RHDjapan from D-speed in Japan the price was very good for a carbon bonnet so good infact i was a little unsure how much i trusted it, decided to bite the bullet and with the help of jesse streeter in not long at all it was at my door. Once it was delivered i ran in from work and quickly unboxed it and to my surprise the quality was actually pretty good i quickly removed the old bonnet and placed on the new one to test it out and even the fitment wasnt too bad at all. Then decided to paint the little grille in the bonnet black to stop it sticking out so much.   I decided to not mess around with the hood latch and just install some aero catch hood pins, having never installed them before did some YouTube university classes and i was good to go. fair to say it is not a fun job at all from making brackets so the pins sit nicely and actually cutting through the bonnet but also being very scared of cutting the holes too big it took wayyyy longer than i would like to admit but finally got it there. Then it was time for a quick test drive to ensure the latches actually worked and thankfully the bonnet looked very stable. I still think paint matching the bonnet and leaving just the part that sticks up as carbon would help make it all look alot neater as im not sure how i feel about all that carbon on a very fridge white car but will leave it as is and see how i feel with time.  
    • I think it's bound to happen, you finally get it all perfect, and bam, something will happen. I took a while to get a Commodore rear quarter repaired where a P Plater clipped it. Two days after getting it back, Sarah wiped it out on a concrete pillar in an underground car park... This is why I take forever to repair them, it stretches how long until it gets bent again... 😛
    • Nah, not really responsible for that little fiasco, but I'm still pissed at myself for writing off my 86, or when I reversed my VX into a pole just before selling it, but, meh, 5hit happens to stuff, all it takes is a slight distraction, and life is full of distractions, and "dooh" moments   
×
×
  • Create New...